Manuale d’uso / di manutenzione del prodotto CD42M del fabbricante Desa
Vai alla pagina of 19
This fireplace is manufactured for Stylecrest Inc. under the Coleman brand nam e by DESA International Inc. DESA INTERNATIONAL 2701 INDUSTRIAL DRIVE P/N 109194-01 P.O. BOX 90024 REV D BOWLING GREEN, KY 42101-9004 10/02 www.desatech.com SAVE THIS BOOK This book is valuable.
- 1 - For more information, visit www.desatech.com CONTENTS 1. INTRODUCTION ------------------------------------------------------------ PG. 2 2. SELECTING LOCATION ------------------------------------------------------------- PG. 2 3. MINIMUM CLEARANCES ------------------------------------------------------------- PG.
-2 - For more information, visit www.desatech.com INTRODUCTION Models CD32M series, CD36M seri es and CD42M are heat circulating gravity direct vent gas fireplaces with sealed combustion chamber. These fireplaces use millivolt gas control valve and millivolt ignition system.
-3 - For more information, visit www.desatech.com In selecting a location, the following precautions m ust be observed: Do not connect this appli a nce to a chimney system used for solid fuel burning fireplace. Due to high temperat ures, do not locate this ap pliance in high traffic areas or near furniture and draperies.
-4 - For more information, visit www.desatech.com VENT PIPE AND TERMINATION CLEARANCES The final position of your appl iance depends on the location of th e term ination in relation to the clearances that must be obse rved. A= 12” (305mm ) clearance above grade, veranda, porch, deck or balcony.
-5 - For more information, visit www.desatech.com VENT INSTALLATION INSTRUCTIONS 1. Install pipe to fireplace collar adapter located on back of unit at a 45 deg. Angle. Connect our starting pipe to a 45 deg. Starting section by sliding it over the collar adapter on the fireplace.
-6 - For more information, visit www.desatech.com Refer to the following table fo r clearance between roof and termination. FRAMING Once the final location has been determ ined (observing clearances for vent terminati on), you may construct framing using dimensi ons shown in figures 8 and 9, depending on the particular installation.
-7 - For more information, visit www.desatech.com The remote control receiver is factory wired and connected to the convertible gas valve as shown in figure 11. GAS SUPPLY TESTING NOTE : This section is intended as a guide for quali fied technicians installing g as to the appliance.
-8 - For more information, visit www.desatech.com Install a sediment trap between the incoming gas line and the gas control box (see figure 15). The sedim ent trap should extend down a mini mum of 3 i nches (76 mm) bey ond the center of the pipe.
- 9 - For more information, visit www.desatech.com GLASS PANEL REMOVAL Before proceeding, make sure gas control valve is in the “OFF” position. 1. To remove louvers, pull both spri ng latches (located in each end of louver) towards center of appliance simultaneously until diseng aged from locating holes.
- 10 - For more information, visit www.desatech.com • Place log #6 (left log) onto le ft pin of front log (#2) and the smooth surface of rear log (#3). Make sure it is seated properly. • Place log #7 onto right pin of top log (#5). Make sure it is seated properly.
- 11 - For more information, visit www.desatech.com.
- 12 - For more information, visit www.desatech.com CONVERSION KIT This conversion kit is packaged wit h the unit. Please check the contents before beginning t his conversion. • Before proceeding, make sure the gas control valve is in the “OFF” position and all electrical power to the appliance is turned off.
- 13 - For more information, visit www.desatech.com • Install the identification label enclosed with th e gas valve regulator to the valve body where i t can easily be seen (see figure 23). FACE EXTENSION (FOR MODEL CD32M ONLY) Model CD32M comes equipped with a front face extension.
- 14 - For more information, visit www.desatech.com OBSERVED PROBLEM POSSIBLE CAUSE REMEDY • Pilot will not stay lit after carefully following ligh ting instructions. • Pilot lit but no flame on the burner. • Frequent pilot outage problem . • Defective pilot generator (thermocouple).
- 15 - For more information, visit www.desatech.com ILLUSTRATED PARTS BREAKDOWN MODELS CD32M AND CD36M SERIES.
- 16 - For more information, visit www.desatech.com ILLUSTRATED PARTS BREAKDOWN MODEL CD42M.
- 17 - For more information, visit www.desatech.com ILLUSTRATED PARTS LIST ITEM DESCRIPTION Q TY. CD32M CD36M CD42M 1 108878-01 108008-01 108326-01 FIREBOX ASSEMBLY 1 2 108874-01 108009-01 108327-01 F.
- 18 - For more information, visit www.desatech.com ACCESSORY AND REPLACEMENT PARTS.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Desa CD42M è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Desa CD42M - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Desa CD42M imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Desa CD42M ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Desa CD42M, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Desa CD42M.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Desa CD42M. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Desa CD42M insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
