Manuale d’uso / di manutenzione del prodotto AE092FCAJA, AE182FCAJA del fabbricante Haier
Vai alla pagina of 35
AE182FCBJA 0010572352 Household MR V Ceiling Concealed T ype Room Air Conditioner CEILING CONCEALED TYPE AIR CONDITIONER INDOOR UNIT AE182FCBJA AE092FCAJA AE182FCAJA 5 8 Health and power failure compe.
1.
2 21 */15.5* AE092FCBJA,AE182FCBJA 21 */18* AE092FCAJA,AE182FCAJA.
3 R407C:AE092FCBJA AE182FCBJA 4 2 9 7 13 SWING NEW FAN SET LOCK RESET 10 1 3 5 6 8 12 ** HEALTH FAN SPEED TIMP MODE SLEEP CLOCK TIMER ON OFF * AUTO % SET ROOM ON OFF MODE FAN TEMP CLOCK SET TIMER SLEEP RESET FILTER RESET ON/OFF HEALTH R22: AE092FCAJA AE182FCAJA SWING 1.
* AUTO % SET ROOM ON OFF MODE FAN TEMP CLOCK SET TIMER SLEEP RESET FILTER RESET ON/OFF HEALTH Operation 4 1.When using remote controller , first point it to the receiving window of wire controller , and then operate remote controller . A ìtickî tone will be uttered to indicate a right acceptance.
5 NOTE:The wired remote controller is supplied by factory along with the indoor unit,but the remote controller should be purchased separately . Battery loading Batteries are fitted as follows: * * * Make sure that the remote controller is used within 7 meters from receiver window of the wire controller and there are no obstructions in between.
Important Points of Safety The following four important points of safety and suggestions should be paid great attention: W arning: Misuse may cause fatal result such as death or serious injury etc. Attention: Misuse may cause human injury or damage of machine, in some case fatal results.
Important Points of Safety W arning l Avoid your body being blown directly by cold wind for long period, otherwise your health may be affected. l Donít extend your fingers or any other article into the inlet or outlet during operation of the machine for touching re- volving fans may cause human injury or damage of machine.
8 Important Points of Safety Attention Attention points for use * Ensure ventilation of the room if the machine is used with burning facilities. Deficient ventilation can cause oxygen shortage. * Check whether installation bench of the machine is damaged after a long period of use.
Operating instructions 9 Fan operation Enjoy yourself by just a gentle press. (1) Unit start (2) Select operation mode (3) Fan Press ON/OFF button, unit starts. Previous operation status appears on display . (Not T imer setting) Power indicator lights up.
Operating instructions 10 * AUTO MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESET FILTER RESET ON/OFF 1 5 2 3 4 SET SWING NEW FAN SET LOCK RESET ** HEALTH FAN SPEED TIMP MODE SLEEP CLOCK TIMER ON OFF 5 LOW MID HIGH AUTO AUTO LOW MID HIGH A U T O AUTO AUTO RUN, COOL,HEAT and DRY operation Use COOL in summer.
SWING NEW FAN SET LOCK RESET ** HEALTH FAN SPEED TIMP MODE SLEEP CLOCK TIMER ON OFF Operating instructions 1 1 TIMER operation Hints: Set Clock correctly before starting Timer operation. You can let unit start or stop automatically at following time: Before you wake up in the morning, or get back from outside or after you fall asleep at night.
12 * ON OFF MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESET FILTER RESET ON/OFF PM AM 1 5 6 4 2 3 SET blank ON OFF ON OFF TIMER ON-OFF Operation mode will be displayed on LCD. Power indicator lights up. Every time the button is pressed, display changes as follows: Select .
Operating instructions about 6 hrs 1 hr 1 hr increase 1 * increase 1 * At night, before going to bed you can press down the SLEEP button on the controller and the air- conditioner will run by the comfortable sleeping mode to make you sleep more comfortable.
Operating instructions 14 SWING COMFORT SET LOCK RESET LIGHT HEALTH FAN TIMP MODE SLEEP CLOCK TIMER ON OFF * MODE FAN HEALTH TEMP CLOCK SET TIMER SLEEP RESET FILTER RESET ON/OFF AM SET OFF 1.
T roubleshooting The following cases are not troubles. During operation , the air conditioner may sometimes exhibit a sound of "clatter " or "rumble " . This is the common sound of refrigerant flow but not a trouble. A sound of "Pi-Pa " is generated.
T roubleshooting ON OFF During DRY operation, there is no air sent out or fan speed cant be changed. In HEAT mode , the outdoor unit generates water or steam. This occurs during removal of the frost (in defrosting operation) on the radiator of outdoor unit.
When fault occurs Poor cooling or heating Is the operation controller adjusted as required? Are there any obstructs before the air inlet or outlet? Is there any door or window left open? Poor cooling .
Notice to users Notice to users l To ensure proper operation of the system , the user shall follow this instruction manual to install the unit. l When handling the air conditioner , please be care not to scratch the case surface.
Installation precautions 19 W arning ! Before installing, do read this "Safety precautions" carefully to guarantee the proper installation. The below attentive matters are divided into" ! W arning " and " ! Note" two parts.
Installation precautions This description does not address to all possible cases. For new requirement and query, please consult the regional sales center of Haier Air Conditioner General Co.
l The power supply shall be connected from the outdoor side. (For models with electric-aided heating function, the power supply to the indoor unit shall be connected at the indoor side The power cord size is 3 G(1.
Installation procedure Fig 1 Choosing the installation location Please do not install the unit in places where flammable gases may be leaked. In case that gas is leaked and accumulated around the unit, it may cause dangers of fire etc. The indoor unit shall be installed at locations where cold and hot air could evenly circulated.
650 223 Installation procedure Fig 2 AE092FCAJA Installation of indoor unit l The unit shall be installed according to the specifications to resist to strong wind and earthquake. Improper installation may cause dangers of unit falling down etc. After selecting the unit installation location, proceed the following steps: 1.
Installation procedure Installation of indoor unit l When installing the ceiling concealed type indoor unit, a specially designed return air bellows shall be installed, as shown in Figure 3, Figure 4.
Installation procedure Installation of indoor unit 25 Indoor unit flexible joint or static pressure box transitive air duct circular air duct joint of air diffuser air diffuser Fig1: Duct connected **.
Installation procedure Installation of indoor unit Installing the suspension screw: Use M8 or M10 suspension screws (4, prepared in the field) (when the suspension screw height exceeds 0.
Installation procedure Installation of remote controller Upper part of wire Use shielede wires for telecommunication between wire controller and indoor unit; indoor unit and outdoor unit. Ground the shield on one side. Otherwise misoperation because of noise may occur .
28 Installation procedure Drain pipe ! Caution l In order to drain water normally, the drain pipe shall be processed as specified in the installation manual and shall be thermal insulated to avoid dew generation. Improper hose connection may cause indoor water leakage.
Installation procedure R efrigerant piping l In installation, if there is refrigerant gas leakage, please take ventilation measures immediately. The refrigerant gas will generate poisonous gas upon contacting fire. l After installation, please verify that there is no refrigerant leakage.
Installation procedure R efrigerant piping V acuum pumping W ith a vacuum pump, create vacuum from the stop valve of the outdoor unit. l Emptying with refrigerant sealed in the outdoor unit is absolutely forbidden. Open all valves Open all the valves on the outdoor unit.
Installation procedure Electric wiring l The electric wiring work shall be conducted by qualified electricians according to the install- ation instructions. A separate power circuit shall be used. Insufficient power cord amperage or improper wiring will cause danger of electric shock or fire.
32 Installation procedure Electric wiring Wiring connection method : (the wiring diagram is attached inside the machine) 1) Ring terminal connection method If there is a ring at the end of the connection wire, the wire connection method is as shown in the right figure.
Installation procedure Field setting Field setting Field setting the unit number In order to realize central control of the MRV air conditioning system, its necessary to set the indoor unit number (control address). Indoor unit number setting Indoor unit number setting switch and confirmation of the settings.
W rap the connection pipe, the drain pipe and the connection wire together with PVC tape..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Haier AE092FCAJA, AE182FCAJA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Haier AE092FCAJA, AE182FCAJA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Haier AE092FCAJA, AE182FCAJA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Haier AE092FCAJA, AE182FCAJA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Haier AE092FCAJA, AE182FCAJA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Haier AE092FCAJA, AE182FCAJA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Haier AE092FCAJA, AE182FCAJA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Haier AE092FCAJA, AE182FCAJA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
