Manuale d’uso / di manutenzione del prodotto HBF855TVE del fabbricante Haier
Vai alla pagina of 18
Automatic Drum W ashing Machine HBF1055TVE HBF855TVE T able of Contents Before using Names of Parts---------------------------------inside front cover Matters Needing Attention------------------------.
Names of Parts T able Cover Program Knob Operation Button Drainage hose clip Back plate Packing bolt (3) W ashing Allocating box W ash Door Observing Glass Window Drainage hose Earth terminal Power su.
Safety 1. A separate earthed socket is required for the power supply . After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni- cian or a Haier designated service point for power cable replacement.
Matters Needing Attention 2 Use ƽ.
9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 4. Do not wash foam rubber or similar sponge materials. 5. Before washing, do up zippers, buttons , laces and repair damaged areas,under- wear or small articals should be placed in the laundry bag or a pillowslip.
As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during trans- portation The steps below should be followed before using the appliance, 1.
Connection of water inlet hose and washing machine W a t e rd r a i n a g eh o s e Connection of power supply The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine.
6 C o n t r o l P a n e l T urn the knob at "0", then turn of f the power and turn the program knob for setting desired wash program. The program knob will not rotate with the programmed washing process.
7 Operational Functions Extra Rinse Button Soak Button Pause/Start Button Press this button,the washing machine will not drain before the final spin-drying cycle.a soaking cycle will be started,and the inner drum will rotate once every 4 minutes(at both directions).
Program Selection 8 Heavy Prewash Normal Light Delicate Normal Light Delicate Normal Delicate Normal Delicate Silk 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 V ery heavy soil Non-fade heavily soiled woolen.
1. Power supply Plug in the power supply 120V~/60Hz. 3. Laundry treament 2. W ater supply T urn on the tap ensure that the water is clear . Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak.
1. Laundry loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing machine, let it run un- loaded for one program to pre- vent the laundry from being tainted by oil or dirty water from the washing machine.
11 6. End W ait 2-3 minutes after the washing process is finished , press the power button again to cut off the power supply . Open the door to take out the laundry .
Other Functions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again.
Insert the bolts. 5. If the machine is to be moved a distance location, replace the vibration mounting locks which were re- moved during installation as shown below. 1. T urn of the water and electricity supply af- ter every wash. Open the door to prevent the formation of moisture and odors.
The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem Possible Cause The washing machine fails to operate Poor co.
Model Maximum working current (A) W ater pressure (MPa) W ashing power (W) Spinning power (W) Spinning speed (r/min) Size (HXDXW) (mm) W eight (kg) HBF1055TVE 120V~/60Hz 13 0.
W iring Circuit 16 Motor M1 M2 M3 M5 M7 M8 CN2-1 CON8 CON6 CN3-3 CN2-3 CN2-5 CN2-7 CN2-9 CN2-11 CON3 CN3-5 CN3-7 CON2 CON1 PCB N G L FA MRN MRL MRC MR EVF EVP PS EVC 12 13 14 11 P PCB-Printed Circuit .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Haier HBF855TVE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Haier HBF855TVE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Haier HBF855TVE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Haier HBF855TVE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Haier HBF855TVE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Haier HBF855TVE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Haier HBF855TVE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Haier HBF855TVE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
