Manuale d’uso / di manutenzione del prodotto HUSQVARNA LGT2554 del fabbricante Husqvarna
Vai alla pagina of 48
LGT2554 Owner's Manual / 96043006100 / 2009-04 03002.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Keys Mower (1) Wheel (5) Large Retainer Springs - 7/16 (2) Smaller Retainer Springs - 5/16 (1) Locknut 3/8-16 (1) Oil Drain Tube For Future Use (1) Shoulder Bolt Mower Front Wheel (1) 3/4 O.D. Washers (1) Anti-Sway Bar (1) Front Link Assembly (1) 1-1/4 O.
6 Fig. 1 02931 CHECK BA TTERY (See Fig. 1) • Lift hood to raised position. NOTE: If this battery is put into service after month and year indicated on label (L) (label is located between terminals) charge battery for minimum of one hour at 6-10 amps.
7 AS SEMBL Y INST ALL MOWER AND DRIVE BEL T (See Figs. 4-12) Be sure tractor is on level surface and engage park ing brake. • Lower attachment lift lever to it's lowest position. CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever , lower it slowly and engage in lowest position.
8 Fig. 12 AS SEMBL Y B F M C S E K D L D A C H • A TT ACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. • Repeat on opposite side of tractor .
9 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models onl.
11 OPERA TION KNOW Y OUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
12 OPERA TION Fig. 14 TO USE CHOKE CONTROL (N) (See Fig. 16) Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.
13 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 18) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. A TO ADJUST GAUGE WHEELS (See Fig. 19) Gauge wheels are prop er ly ad just ed when they are slight ly off the ground when mower is at the desired cutting height in operating position.
14 OPERA TION Fig. 21 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous.
15 SERVICE REMINDER/HOUR METER Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. T o service engine and mower , see the Maintenance section of this manual.
16 Fig. 22 MOWING TIPS • Mower should be properly leveled for best mowing per - formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
17 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
18 MAINTENANCE Fig. 23 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life.
19 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
20 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
21 SERVICE AND ADJUSTMENTS Fig. 27 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key .
22 SERVICE AND ADJUSTMENTS Fig. 29 FRONT - TO-BACK ADJUSTMENT (See Figs. 30 & 31) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 SERVICE AND ADJUSTMENTS TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 32) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L).
24 SERVICE AND ADJUSTMENTS Fig. 33 electric 02953 A B C D E F G H J TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced.
25 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REP AIRS (See Fig. 34) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble.
26 SERVICE AND ADJUSTMENTS Fig. 36 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
27 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
28 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
29 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
30 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
31 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
32 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V Outl.
33 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Bat.
34 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 CHASSIS 182 68 68 176 176 176 175 178 228 165 228 183 194 236 150 180 68 68 213 213 52 218 34 130 130 177 189 189 152 217 235 3.
35 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 CHASSIS KEY P ART NO . NO . DESCRIPTION 5 532 40 87-01 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille.
36 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 DRIVE 56 216 143 125 226 125 125 80 125 51 231 170 175 279 176 178 174 22 23 166 232 153 233 drive-tex_K46_fender_14 64 161 184.
37 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 DRIVE KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 62 - 06 T ransaxle, TUFF TORQ K46 AW 2 532 18 62-11 Key 7 532 19 98-44 Hub Asm.
38 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 ENGINE 2 29 SP ARK ARRESTER KIT 21 20 Engine-tex_Kohl-2cyl_1_r2 18 15 37 28 37 1 84 45 81 82 22 62 87 71 70 79 69 69 12 11 41 4.
39 KEY P ART NO . NO . DESCRIPTION For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Kohler Co.
40 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 STEERING ASSEMBL Y .
41 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 SEA T ASSEMBL Y 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
42 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 MOWER DECK MOWER?DECKªTEX??R .
43 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 40 31-25 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm.
44 TRACTOR - MODEL NO . LGT2554 (96043006100), PRODUCT NO . 960 43 00-61 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-tex_3 89 87 89 87 2 532 19 52-23 Shaft Asm.
45 SERVICE NOTES.
46 SERVICE NOTES.
47 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e .
SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the d.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna HUSQVARNA LGT2554 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna HUSQVARNA LGT2554 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna HUSQVARNA LGT2554 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna HUSQVARNA LGT2554 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna HUSQVARNA LGT2554, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna HUSQVARNA LGT2554.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna HUSQVARNA LGT2554. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna HUSQVARNA LGT2554 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
