Manuale d’uso / di manutenzione del prodotto L180p del fabbricante IBM
Vai alla pagina of 33
L180p User's Guide IBM ThinkVision TM Monitor L180p English.
ii i First Edition (January/2004) Note: For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor..
ENGLISH 1 Safety (Read first) .......................................................................................................2 Setting up the monitor .............................................................................................
2.
ENGLISH 3 Always observe the following precautions to reduce the risk of injury and property damage. Do not attempt to service a product yourself unless instructed to do so by the IBM Support Center. Use only an IBM authorized service provider who is approved to repair your particular product.
4 Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.
ENGLISH 5 Setting up the monitor Handling instructions 1. Lift the monitor by placing your hands where indicated by the arrows in the figure below. An alternative is to use the handle feature on the back of the monitor.
6 Kensington security slot Figure A 3. Before adjusting your monitor for the first time, remove the locking clip on rear of the stand. Carefully hold the screen of the monitor and squeeze the locking clip to remove. This action is shown in Figure A. This slot can be used to connect to a locking cable.
ENGLISH 7 7 i With the IBM Flat Panel Monitor, you can adjust its position in various ways for maximum comfort. Viewing angle You can tilt the screen forward and backward as shown below in Figure A. Swivel You can swivel the screen to the left or the right as shown below in Figure A.
8 Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows: • Do not use solvents or abrasives. • Gently wipe the covers and the screen with a soft cloth. • Remove finger marks and grease with a damp cloth and mild detergent.
ENGLISH 9 Connecting your monitor 1. Turn off your computer and all attached devices. Next, unplug all power cords to your computer and all attached devices. 2. Connect the signal cable. • The analog signal cable is already connected to your monitor (See in Figure A).
10 1. Switch on your computer. 2. Switch on your monitor by pushing and releasing the power switch marked " " at the front of the bezel. • To switch off your monitor, push and release the power switch again. 3. To update or install device drivers, follow the instructions in the Device driver installation section on page 11.
ENGLISH 11 To install the device driver in Microsoft ® Windows ® 95 or Windows 98, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98. 1. Turn off the computer and all attached devices.
12 To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition (Me), do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me.
ENGLISH 13 To install the device driver in Windows XP, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows XP. 1. Turn off the computer and all attached devices.
14 For digital input, image setup is not required. When you first use your monitor, you must perform Auto Setup for analog input. If you are using digital input, continue with the instructions on page 9. This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing.
ENGLISH 15 Image setup for DOS i If the monitor is in standby mode, it may automatically turn off while you are waiting for it to warm up. If this happens, switch off the monitor and switch it on again after a few seconds. i If you are using PC-DOS/V, change to U.
6. When the dot pattern appears, pre s s t h e " " b u t t o n at the bottom of the monitor. This activates the Image setup procedure, which will optimize the display settings with the provided dot-patterns. •The screen will momentarily turn black while auto adjustment proceeds.
Normally, you can complete the setup procedure using Automatic Image s etup; however, if your screen image is still distorted after you perform Image s etup or the setup CD does not run on your system, perform M anual Image s etup . To manually adjust the image setting, do the following: 1.
18 Adjusting your LCD monitor User controls USER CONTROL FEATURES i The image is already optimized for many display modes, however the user controls can be used to adjust the image to your liking. i The settings are saved after adjustment and when exiting the OSD and will be effective thereafter.
ENGLISH 19 The settings adjustable with the user controls are viewed through the On - Screen Display (OSD). Press the ent er but ton "" to display the main OSD menu. Initial appearance of OSD On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day.
20 OSD Icon Select the Color mode you find most comfortable or fine tune the colors using the Custom menu, if necessary. Description Sub-menu(s) • Clock • Phase • Save Increases or decreases red.
ENGLISH 21 Use this button to make the analog or digital connector active. This feature is used when two computers are connected to the monitor. The default setting is analog.
22 i If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT monitor temporarily until you have reconfigured the computer, preferably to 1280 x 1024 at 60Hz.
ENGLISH 23 To benefit from power management, the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association (VESA) Display Power Management Signaling (DPMS) Standard.
24 Arm or wall mounting i Be sure to read the Monitor Safety and Warranty Information manual that comes with your monitor before changing stands or cables.
ENGLISH 25 T roubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem No power to monitor.
26 i For image problems, you may want to run Image setup again before consulting to this section. In most cases, Image setup can fix the problems. See Automatic Image setup for the computer on page 14 for details. Problem Possible Cause Suggested Action Reference There are noises in the video signal The color setting may be incorrect.
ENGLISH 27 If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM Service and Support. In the U.S.A and Puerto Rico call 1-800-772-2227 In Canada (Toront.
28 i Power consumption figures are for the monitor and the power supply combined. Specifications This color monitor (Type-model 9180-Hxx) uses a 18.1-inch TFT LCD. Weight 5.3 kg (11.684 lbs) 7.7 kg (16.975 lbs) Without Stand: With Stand: 18.1inch (459.
ENGLISH 29 FRU Monitor FRU Stand FRU Video Interface Cable FRU Video Interface Cable Hybrid Hybrid Analog 3.0 Meter Digital 3.0 Meter Black Black Black Black 9180-HB9 9180-HB9 9180-HG9 9180-HB9 9180-H.
30 Notices and trademarks This section contains information on notices and trademarks. Notices IBM may not offer the products, services, or feature discussed in this document in all countries. Consult your local IBM representative for information on the products and services currently available in your area.
ENGLISH 31 Trademarks The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other countries, or both; IBM IBM logo ThinkPad E NERGY S TAR and the E NERGY S TAR logo are U.S Govt. registered trademarks.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il IBM L180p è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del IBM L180p - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso IBM L180p imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul IBM L180p ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il IBM L180p, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del IBM L180p.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il IBM L180p. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo IBM L180p insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
