Manuale d’uso / di manutenzione del prodotto 4304 del fabbricante Makita
Vai alla pagina of 20
Jig Saw Model 4304 4305 MODEL 4304 MODEL 4305 Variable Speed Variable Speed Length Max. cutting capacities Strokes Overall Net of stroke Wood Mild steel Aluminum per minute length weight 249 mm (9-314") 2.
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 2. Don't cut hollow pipe. 3. Do not cut oversize workpiece. 4. Check for the proper clearance beneath the workpiece before cutting so that 5.
The followings show the symbols used for tool. v ................................. volts A ................................. amperes Hz ................................. herts kg ................................. kilograms h ..........................
Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the blade. To install the blade, loosen the screw on With the blade teeth facing forward, insert 1 the blade into the blade holder as far as it will go.
Installing the universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.
Position Cutting action Applications I ~~~ ~~~~ ~ ~ ~ ~ ~~~ I I I Smallorbit cutting action 1 For cutting mild steel, aluminum and hard wood. straight line cutting action 0 For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood.
Speed adjusting dial The tool speed can be adjusted and maintained between 500 and 3,000 strokes per minute by turning the adjusting dial. The dial is marked 1 (lowest speed) to 6 (full speed). Workpiece to be cut 1- Lock lever :or 4304 Number on adjusting dial Refer to the table at right to select the proper speed for the workpiece to be cut.
CAUTION : Always hold the tool with the base flush with the workpiece. Failure to do so may cause *Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may a slanted cutting surface and blade breakage. cause a slanted cutting surface and blade breakage.
cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cutouts without a lead-in cut from an edge, predrill starting hole more than 12 mm (15/32") in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut.
Finishing edges To trim edges or make slight dimensional adjustments, run the blade lightly along the cut edges. 'Of I For 4305 Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear.
Guide rule (rip fence; optional accessory) When cutting widths of under 150 mm (5-29/32") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To install it, loosen the bolt on the front of the base. Slip in the guide rule and secure the bolt.
To attach the vacuum head on the tool, insert the hook of the vacuum head into the hole in the base. Tighten the bolt to secure the vacuum head. Then connect a Makita vacuum cleaner to the vacuum head.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Jig saw blade Blade type No. 51 Application ' Wood and plywood Plastics Aluminum 1.5 - 3 mm thick 1 - 6 mm thick - 11/16" - 118") 13/64' - 1/4'l H 4 - 60 mm thick 4 - 60 mm thick NO. 58 I 15/32" - 2-3/6"1 15/32" - 2-318") I- Is No.
JIG SAW Model 4304 Note: The switch, noise suppressor and other part configurations may differ from country to country. 17.
MACHINE ~ 1 1 Switch 2 1 Handle Set IWith Item 551 3 1 Tapping Screw Flange PT 4x20 4 1 Cord 5 1 Cord Guard 6 1 Strain Relief 7 2 Tapping screw 4xia 9 1 PI" 3 10 1 Switch Lever 11 1 Spacer 12 1 C.
JIG SAW Model 4305 Note: The switch, noise suppressor and other part configurations may differ from country to country. 19.
MAKlTA LIMrrED ONE YEAR WARRANTY I Warranty Policy Every Makita tool is thorou ly inspezted and tested before leaving the factory. It is warranted to be free of defects from wor&kp and materials for the period of ONE YEAR from the date of original purchrsc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 4304 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 4304 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 4304 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 4304 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 4304, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 4304.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 4304. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 4304 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.