Manuale d’uso / di manutenzione del prodotto LS0711Z del fabbricante Makita
Vai alla pagina of 32
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.
2 SPECIFICATIONS Blade diameter : ......................................................................................... 190 mm (7-1/2”) Hole (arbor) diameter : ............................................................................... 15.88 mm (5/8”) Max.
3 1. KNO W Y OUR PO WER TOOL. Read the owner’ s manual carefully . Learn the tool’ s applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GU ARDS IN PLAC E and in working order . 3. REMO VE ADJUSTING KEYS AND WRENCHES.
4 23. POLARIZED PLUGS. T o reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, re verse the plug.
5 a vise during all operations. Never use your hand to secure the w orkpiece . 5. Never reach ar ound saw blade. 6. T urn off tool and wait for saw blade to stop before mo ving workpiece or chang- ing settings. 7. Unplug tool before c hanging blade or ser- vicing.
6 29. NEVER hold workpiece on right side of blade with left hand or vice versa. This is called cross-armed cutting and e xposes user to risk of SERIOUS PERSONAL INJUR Y as shown in the figure. AL W A YS use vise to secure workpiece. 30. Do not abuse cor d.
7 INST ALLA TION Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin. Release the stopper pin b y lower- ing the handle slightly and pulling the stopper pin. This tool should be bolted with two bolts to a le vel and stab le surf ace using the bolt holes provided in the tool’ s base.
8 If the see-through blade guard becomes dirty , or sawdust adheres to it in such a wa y that the blade is no longer easily visible , unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or an y petroleum-based cleaners on the plastic guard.
9 Maintaining maximum cutting capacity This tool is fa ctor y adjusted to provide the maximum cutting capacity f or a 190 mm (7 - 1/2 ” ) saw blade . When installing a new b lade, alwa ys check the lo wer limit position of the blade and if necessary , adjust it as follo ws: First, unplug the tool.
10 Adjusting the miter angle Loosen the grip by turning counterclockwise. T ur n the turn base while pressing down the loc k lev er . When you hav e mov ed the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise .
11 • Do not pull the s witch tr igger hard without pressing in the lock-off b utton. This can cause switch breakage . T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, press in the loc k- off button and pull the s witch trigger .
12 Socket wrenc h storage The sock et wrench is stored as shown in the figure. When using the sock et wrench, pull it out of the wrench holder . After using the sock et wrench, retur n it to the wrench holder .
13 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise. Then remo ve the he x bolt, outer flange and blade. T o install the blade, mount it carefully onto the spindle , mak- ing sure that the direction of the arrow on the surf ace of the blade matches the direction of the arro w on the blade case.
14 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out.
15 V ertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assemb ly (optional accessor y). Inser t the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod.
16 Holders and holder assembl y (optional accessories) The holders and the holder assembly can be installed on either side as a conv enient means of suppor ting workpieces horizontally . Install them as shown in the figure . Then tighten the screws firmly to secure the holders and the holder assembly .
17 1. Press cutting (cutting small workpieces) W or kpieces up to 50 mm (2 ” ) high and 97 mm (3-13/16 ” ) wide can be cut in the f ollowing wa y . Push the carriage toward the guide f ence fully and tighten the clamp screw on the turn base clockwise to secure the carriage.
18 • Ne ver perf or m the slide cut with the handle lock ed in the lowered position b y pressing the stopper pin. • Ne ver loosen the clamp screw which secures the carriage while the blade is rotating. This ma y cause serious injur y . 3. Miter cutting Ref er to the previously cov ered “ Adjusting the miter angle ” .
19 When perfo r ming compound cutting, refer to “ Press cut- ting ” , “ Slide cutting ” , “ Miter cutting ” and “ Be vel cut ” e xplanations. 6. Cutting cro wn and cove moldings Crown and co ve moldings can be cut on a compound miter saw with the moldings laid flat on the turn base.
20 Example: In the case of cutting 52/38 ° type crown molding f or position (1) in Fig. A: • Tilt and secure be vel angle setting to 33.9 ° LEFT . • Adjust and secure miter angle setting to 31.
21 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings 000031 52 ˚ 38 ˚ Ceiling W all W all to Crown Molding Angle: 52/38 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.
22 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings 000032 45 ˚ 45 ˚ Ceiling W all W all to Crown Molding Angle: 45 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.
23 7. Cutting aluminum ex trusion When securing aluminum e xtr usions, use spacer b locks or pieces of scrap as shown in the figure to pre v ent def or mation of the aluminum. Use a cutting lubricant when cutting the aluminum e xtrusion to prev ent build-up of the aluminum material on the blade.
24 9. Cutting repetitive lengths When cutting se veral pieces of stoc k to the same length, ranging from 220 mm (8 - 5/8 ” ) to 385 mm (15 - 1/8 ” ), use of the set plate (optional accessor y) will f acilitate more efficient operation. Install the set plate on the holder (optional accessor y) as shown in the figure.
25 Carr y the tool by carrying grip as shown in the figure. If y ou remov e the holders, dust bag, etc., you can carry the tool more easily . CA UTION: • Alwa ys secure all moving por tions before carrying the tool. • Stopper pin is f or carr ying and storage pur poses only and not f or any cutting operations.
26 Make sure that the pointer points to 0 ° on the miter scale. If the pointer does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . 2. Bevel angle (1) 0 ° be vel angle Push the carriage toward the guide f ence and tighten the clamp screw on the turn base to secure the carriage.
27 Make sure that the pointer on the arm point to 0 ° on the be vel scale on the arm holder . If it does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . (2) 45 ° be vel angle Adjust the 45 ° be vel angle only after perf or ming 0 ° be vel angle adjustment.
28 After use • After use, wipe off chips and dust adhering to the tool with a cloth or the like . Keep the b lade guard clean according to the directions in the pre viously covered section titled “ Blade guard ” . Lubricate the sliding por tions with machine oil to prev ent rust.
29 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
30 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2.
31 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St.
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th defects or other reproductiv e har m.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita LS0711Z è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita LS0711Z - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita LS0711Z imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita LS0711Z ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita LS0711Z, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita LS0711Z.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita LS0711Z. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita LS0711Z insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
