Manuale d’uso / di manutenzione del prodotto LM86 del fabbricante Arrow Plastic
Vai alla pagina of 32
* Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
2 Owner's Manual Bef ore beginning constr uction, chec k local building codes regarding f ootings , location and other requirements. Study and understand this owner's manual. Impor tant infor mation and helpful tips will mak e your construction easier and more enjo ya ble.
3 Selecting and Pr eparing Y our Site: Bef ore assembly , y ou will want to decide on a location f or your b uilding. The best location is a le v el area with good drainage. •Allow enough working space for ease of moving parts into position during assembly.
4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing.
Finish: F or long lasting finish, per iodically clean and w ax the exterior surf ace. T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per man ufacturer's recommendation.
ACCESSORIES.... A6 WEB 6 * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7.
THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8.
The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation B09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: ARROW FLOOR FRAME KIT : (Order No . FB106-A or 68381-A) Arrow has the best base for your building in this simple kit.
It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation.
11 Remove from bag of screws and save for the last step 67293 Weather Stripping (1) 66029 Plug (2) (Packed with Screws) 66382 Lower Door Guide (4) 66183 Roof Trim Cap (2 right & 2 left) 66045 Hand.
Parts List P12 12 Assembly P a r t P a r t Quantity Check K e y No . Number Description i n C a r t o n List 1 6615 Rear W all Angle 2 2 6617 Door T rac k Splice 1 3 10498 Horizontal Door Brace 4 4 66.
13 Assembly by Key No. B13.
The front floor frame is made up of three pieces. The rear floor frame is made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the front and rear.
S tep 2 B15 15 ● P ar ts Needed F or ● Frame Assemblies ● ● ● ● ● 6615 Rear Wall Angle (2) ● ● ● ● ● 9924 Rear Wall Channel (2) The main frame pieces reinforce the walls. These pieces will later be in- stalled in the center and at the top edge of the rear wall.
16 S tep 3 B16 ● P ar ts Needed F or ● Roof Beam Assembly ● ● ● ● ● 8474 Roof Beam (1) ● ● ● ● ● 8476 Side Wall Angle (1) The roof beams join the two gables and support the roof panels. The main roof beam is made up of two pieces fastened together.
17 NOTE: Door Track Splice (painted part) S tep 4 B17 ● P ar ts Needed F or ● Door T rack Assembly ● ● ● ● ● 6617 Door Track Splice (1) ● ● ● ● ● 9378 Door Track (2) The door track assembly supports the sliding doors and reinforces the front wall.
● ● ● ● ● Front Floor Assembly (1) ● ● ● ● ● 8946 Side Floor Frame (2) ● ● ● ● ● Rear Floor Assembly (1) ● P ar ts Needed F or ● Floor Frame S tep 5 B18 The floor frame must be square and level or holes will not align.
1 Position the rear corner panels at the rear corners, as shown. The wid- est part of each rear corner panel must be placed along the rear of the building. Attach the corner panels to the floor frame with four screws. 2 Position a front corner panel at the corner of the floor frame as shown.
● P ar ts Needed F or ● Frames S tep 7 B20 20 ● ● ● ● ● Door Track Assembly (1) ● ● ● ● ● Rear Wall Angle Assembly (1) ● ● ● ● ● 8476 Side Wall Angle (2) ● ● ● .
21 ● ● ● ● ● 6515 Wall Panel (4) ● ● ● ● ● 6243 Wall Panel (2) ● P ar ts Needed F or ● W all Panels S tep 8 P21 The wall panels come in two widths. Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it.
22 ● P ar ts Needed F or ● Door Jamb S tep 9 P22 ● ● ● ● ● 9369 Door Jamb (2) The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten a door jamb to the front panel with three bolts, nuts and acorn nuts, as shown.
23 The gables go on top of the front and rear walls to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. 1 Attach the four roof beam brack- ets to the gables using two bolts, washers and nuts.
24 S tep 1 1 B24 ● P ar ts Needed F or ● Gables/Braces ● ● ● ● ● Left Gable Assembly (2) ● ● ● ● ● Right Gable Assembly (2) ● ● ● ● ● 6658 Gable Brace (2) 1 Lift and fasten a right and left gable, under angle at corner, to the rear wall angle with screws.
25 S tep 12 B25 ● P ar ts Needed F or ● Roof Beams ● ● ● ● ● Main Roof Beam (1) ● ● ● ● ● 8474 Roof Beam (2) 1 Fasten the main roof beam to the gable brace of the front gable. 2 Fasten the other end of the main roof beam to the gable brace of the rear gable.
26 S tep 13 B26 ● P ar ts Needed F or ● Right Roof Panel ● ● ● ● ● 8466 Right Roof Panel (1) Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer.
1 Install a left roof panel at the left rear and right front corner of the roof. Install a right roof panel at the left front corner of the roof. 3 Install 4 roof panels in the se- quence and positions shown on pre- vious page. Do not fasten the lower end of the panels to the side wall angles at this time.
28 S tep 15 B28 ● P ar ts Needed F or ● Ridge Cap ● ● ● ● ● 8461 Ridge Cap (1) 1 Install the ridge cap on the com- pleted roof section using bolts and nuts. Do not fasten the ends of the ridge cap at this time. 2 Fasten the lower end of the panels to the side wall angles using screws and washers.
29 S tep 16 B29 ● P ar ts Needed F or ● Roof T rim ● ● ● ● ● 8482 Side Roof Trim (2) 1 Attach the side roof trim to the lower end of the roof panels on each side of the building using screws at each panel overlap.
30 END VIEW SHOWING: S tep 17 P30 ● P ar ts Needed F or ● Door Assembly ● ● ● ● ● 10478 Right and Left Doors (2) ● ● ● ● ● 10498 Horizontal Door Brace (4) ● ● ● ● ● 6278 Vertical Door Brace (2) The steps on this page tell how to assemble the right door.
31 S tep 18 P31 ● P ar ts Needed F or ● Door Installation & Adjustment ● ● ● ● ● Right Door Assembly (1) ● ● ● ● ● Left Door Assembly (1) 1 From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track.
SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Arrow Plastic LM86 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Arrow Plastic LM86 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Arrow Plastic LM86 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Arrow Plastic LM86 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Arrow Plastic LM86, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Arrow Plastic LM86.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Arrow Plastic LM86. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Arrow Plastic LM86 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
