Manuale d’uso / di manutenzione del prodotto P600 del fabbricante NEC
Vai alla pagina of 24
NEC V ersa P600 Disassembly Manual.
NEC Versa P600 Disassembly Manual Page 2 Table of contents Overview ....................................................................................................................... ..........................................3 Technician Notes ..
NEC Versa P600 Disassembly Manual Page 3 Overview This document contains step-by-step di sassembly instructions for the Versa T400 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled.
NEC Versa P600 Disassembly Manual Page 4 Hazardous Voltage There is hazardous voltage present inside the computer when it is connected to an AC supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury.
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa P600. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of it s place as the arrow shows in Fig.
2. Lift up the hard disk drive and disconnect it as shown in Fig. 3 Fig. 3 Disconnecting the hard disk drive 3. Unscrew the four screws on both sides of the hard disk drive as shown in Fig.
2. Carefully lift up MDC modem module. 3. Disconnect the cable attached to the MDC modem and put the modem aside. Removing the Keyboard Cover NEC Versa P600 Disassembly Manual Page 7 To remove the Keyboard Cover , first remove the battery (see Removing the Battery ), then perform the following steps: 1.
NEC Versa P600 Disassembly Manual Page 8 1. Remove the screws as shown in Fig. 8 Fig. 8 Removing the screws holding the keyboard Note: The screw “A” located on the hard disk slot cove r holds the hard disk dr ive and the key board. 2. Carefully lift up the keyboard.
NEC Versa P600 Disassembly Manual Page 9 Fig. 10 Removing the screws on Heat Plate Note: If you w ant to disassemble the Optical Drive, you are required to release Screw “A” only. 2. Push the Optical Drive module out from the base unit as shown in Fig.
NEC Versa P600 Disassembly Manual Page 10 Fig. 12 Removing Heat plate from base unit Note: When assembling the heat plate, ma ke sure that these three ho cks on the heat plate are properly inserted into the openings located on the top cover.
NEC Versa P600 Disassembly Manual Page 11 Removing the Wireless Module To remove the Wireless Module, first remove the keyboard cover (see Removing the keyboard cover ), remove the keyboard (see Removing the keyboard ), remove the heat plate (see Removing heat plate ), then perform the following steps: 1.
Fig. 15 Releasing the heat sink screws Note: When assembly the heat sink, tighten the heat si nk screw s according to the ascending order (1 2 3 4). This is to ensure a well distributed pressu re over the CPU and to prevent damaging the CPU 2.
NEC Versa P600 Disassembly Manual Page 13 Removing the LCD Module To remove LCD Module, first remove the Keyboard Cover (see Removing the keyboard cover ) then remove the keyboard (see Removing the keyboard ): 1. Unscrew the two LCD connector screws and also, disconnect the speaker connector as shown in Fig.
NEC Versa P600 Disassembly Manual Page 14 Fig. 20 LCD hinge screws at the rear 4. Unscrew the two screws located on the bo ttom of the unit as shown in Fig. 21 Fig. 21 LCD hinge screws at the bottom 5. Carefully lift the LCD module out of the system and put it aside.
Removing the LCD Panel To remove the LCD Panel, first remove the LCD Module (see Removing the LCD Module ), then perform the following steps: 1. Unscrew all screws shown in Fig. 22 Fig. 22 Screws on the LCD Module 2. Release the LCD Bezel carefully and put it aside as shown in Fig.
NEC Versa P600 Disassembly Manual Page 16 Fig. 24 Removing the inverter board screws 4. Carefully lift up LCD panel and disconnect the LCD cable from the penal. 5. Remove the screws at both sides of the L CD panel in order to release the LCD hinges as shown in Fig.
Removing the Top Cover To remove the Top Cover, first remove the Keyboard Cover (see Removing the keyboard cover ), remove the keyboard (see Removing the keyboard ), remove the LCD module (see Removing the LCD Module ) then perform the following steps: 1.
NEC Versa P600 Disassembly Manual Page 18 Fig. 28 Battery Com partment 5. Carefully lift up and release the top cover and put it aside. Fig. 29 Removing the top cover Note: Remember to disconnect the touc h pad cable before lifting up the t op cover. On the VGA connector area use extra care to release the top cover.
NEC Versa P600 Disassembly Manual Page 19 1. On the other side of the top cover unscrew the two screws on the Touch Pad assembly as shown in Fig. 30 and remove the Touch Pad assy from the palm rest.
NEC Versa P600 Disassembly Manual Page 20 Removing the DC/DC Board To remove the DC/DC board, first remove the Top Cover (see Removing the Top Cover ), then perform the following steps: 1. Remove the screw on the DC/DC board as shown in Fig. 31 Fig. 31 DC/DC Board 2.
NEC Versa P600 Disassembly Manual Page 21 Removing the Main Board To remove the Main board, first open the Top Cover (see Removing the Top Cover ), remove DC/DC board (see Removing DC/DC board ) then perform the following steps: 1. Remove the screws holding the main board in place as shown in Fig.
NEC Versa P600 Disassembly Manual Page 22 Fig. 35 Removing Main Board DIP Switch Setting Fig. 36 DIP Switch position Dip Switch Description Seeting Keyboard Select1 Keyboard Select2 ON : Enable OFF: Normal (Default) ON : connect to GND OFF : NC Password override.
NEC Versa P600 Disassembly Manual Page 23 Screws M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver M2.5x11 Black M2.5x12.5 Silver M2.5x15 Black M2x3 Sliver M2x6 Black M3x4 Black M2.
NEC Versa P600 Disassembly Manual Page 24 Notice The information in this guide is subject to change without notice. This guide contains information prot ected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior writt en consent from NEC Computers International BV.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il NEC P600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del NEC P600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso NEC P600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul NEC P600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il NEC P600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del NEC P600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il NEC P600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo NEC P600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.