Manuale d’uso / di manutenzione del prodotto PRO700iE del fabbricante Rackmount Solutions
Vai alla pagina of 24
.
1 © Copyright Para Systems, Inc., 2003 PRO-E Series User's Manual 1 . Introduction 2 2 . Controls and Indicators 5 3. Installation 7 4. Operation 9 5 . T roubleshooting 12 6 . Replacing the Battery 13 7 . Obtaining Service 16 8 . Specifications 17 9 .
2 IMPORT ANT SAFETY INSTRUCTIONS SA VE THESE INSTRUCTIONS ! English Thank you for purchasing a MINUTEMAN power protection product. It has been designed and manufactured to provide many years of trouble free service.
3 W ARNING: Risk of Electrical Shock. Hazardous live parts inside these power supplies are energized from the battery even when the AC input is disconnected. T o de-energize the outputs of the UPS: 1. If the UPS is on press and release the On/Off/T est button.
4 English Para Systems Life Support Policy As a general policy , Para Systems Inc. (Para Systems) does not recommend the use of any of its products in life support applications where failure or mal- f.
5 On-Line On-Battery Buck Boost English On-Line/On-Battery/Boost/Buck LED Overload LED Weak/Bad Battery LED On/Off/T est Button Fault LED Press and release the ON/OFF/T est Button after 1 beep to turn the UPS ON or OFF (see section 4).
6 REAR P ANEL English 5 4 3 2 1 10 8 6 7 9 5 4 3 2 1 8 6 7 9 1. The Information/Rating Label. 2. The Battery Backup and Surge output power receptacles are NEMA 5-15R type (IEC 320 C13 sockets for 230V models). 3. The USB Communications Interface Port is for UPS monitoring and control.
7 INST ALLA TION PLACEMENT The PRO-E series is intended to be install in a temperature controlled environ- ment that is free of conductive contaminants.
8 English DO NOT plug Power Strips or Surge Protection Devices into the ”Battery Backup” Receptacles on the UPS. Plugging Power Strips or Surge Protection Devices into the “Battery Backup” Receptacles may cause internal damage to the UPS, the Power Strip, or the Surge Protection Device.
9 English TURNING THE UNIT ON/OFF ON / OFF / T est Button SELF TEST Press and release the ON/OFF/T est Button after one beep to turn the UPS ON and supply power to the load. The load is immediately powered while the UPS runs a two-second self test. Press and release the ON/OFF/T est Button after one beep to turn the UPS OFF .
10 English ALARMS ON BA TTER Y When the UPS is operating on the batteries, the On-Battery LED will blink and the audible alarm will sound once every 10-seconds. The alarm will stop once the UPS returns to the On-Line operation. UPS F AUL T When the UPS detects a hardware fault, the Fault LED will illuminate and the UPS will sound a constant alarm.
11 COMMUNICA TIONS PORTS (RS232 and USB) The RS232 communication port is a standard DB9 female with both RS232 and simulated contact closure capability . The PRO-E series UPS will poll the port and activate the port for RS232 or contact closure in accordance with the type of cable it finds connected to the port.
12 English Possible Cause Symptom What T o Do Press and release the On/Off/ T est button to start UPS On/Of f/T est button not pushed UPS will not turn on Reset circuit breaker by pressing the plunger back in.
13 REPLACING THE BA TTER Y W ARNING! This Uninterruptible Power Supply contains potentially hazardous voltages. Do not attempt to disassemble the UPS beyond battery replacement procedures below . This UPS contains no user serviceable parts. Repairs and Battery replacement must be performed by AUTHORIZED SERVICE PERSONNEL ONL Y .
14 English BA TTER Y REPLACEMENT PROCEDURE PLEASE READ THE CAUTIONS AND W ARNINGS BEFORE A TTEMPTING TO REPLACE THE BA TTERIES Hot-swappable batteries mean that the batteries can be replaced without powering down the whole UPS system.
15 9. Disconnect the positive (red) wire from the battery positve terminal. 10. Disconnect the battery negative (black) wire from the battery negative terminal. NOTE: Use CAUTION, do not touch the battery positive wire to the battery negative wire. 1 1.
16 English IF THE UPS REQUIRES SERVICE 1.Use the TROUBLESHOOTING section to eliminate obvious causes. 2.V erify there are no circuit breakers tripped. A tripped circuit breaker is the most common problem.
17 Default 120V (230V) / User selectable at 120/127V , (208/230V) 3-5 years, depending on discharge cycles and ambient temp 500V A 350W 700V A 490W 1500V A 1050W 1 100V A 770W 500 J (440 J) 0 ns (instantaneous) normal mode; <5 ns common mode <5% Normal and common mode EMI/RFI suppression 1-12V9Ah 2-12V7Ah 3-12V7Ah Audible noise at 1 m (3 ft.
18 English (These items may require optional software or hardware) Function Factory Default Description User Choices Set inverter output voltage Shut- down T ype Set audible alarm state Enable/ Disabl.
19 English Para Systems Inc. (Para Systems) warrants this equipment, when properly applied and operated within specified conditions, against faulty materials or workmanship for a period of three years from the date of purchase.
20 English EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL P ARA SYSTEMS BE LIABLE FOR DIRECT , INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUEN- TIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT , EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
21 DECLARA TION OF CONFORMITY Application of Council Directive(s): 89/336/EEC, 73/23/EEC Standard(s) to which Conformity is declared: EN50091-1-1, EN50091-2 Manufacturer’s Name: Para Systems, Inc.
22 English Notes:.
Rackmount Solutions, Ltd. 915 S. J upiter Road Garland, TX 75042 www .rackmountsolutions .net sales@rac kmountsolutions.net 1-866-207-6631 | F ax 972-276-6484 GSA Contract # GS-35F-0208R f or IT 70 Ap.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Rackmount Solutions PRO700iE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Rackmount Solutions PRO700iE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Rackmount Solutions PRO700iE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Rackmount Solutions PRO700iE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Rackmount Solutions PRO700iE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Rackmount Solutions PRO700iE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Rackmount Solutions PRO700iE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Rackmount Solutions PRO700iE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
