Manuale d’uso / di manutenzione del prodotto airPoint Pro Series del fabbricante SmartBridges
Vai alla pagina of 28
s m a r t Bridges to the future ... Revision 1.8 Page 1 of 28 airPoint-PRO Series Wireless Access Point Quick Install Guide Installing the airPoint-PRO Series airPoint-PRO is a wireless Access Point to provide WLAN connectivity to any PC. It operates at 2.
Revision 1.8 Page 2 of 28 Contents of Pac kage airPoint-PRO Outdoor l airPoint-PRO Outdoor Unit l powerShot l AC Adapter l Pole Mounting Kit : U Bracket, Nuts, W ashers l W all Mounting Kit : W all pl.
s m a r t Bridges to the future ... Revision 1.8 Page 3 of 28 for airPoint-PRO Outdoor / airPoint-PRO TOT AL Important note - Earthing Requirements: Follow National Electric Code NEC 810-20 and NEC 810-21 for this installation. Mounting the airPoint-PRO Outdoor Fix the airPoint-PRO Outdoor unit with the U bolts to the steel pipe.
Revision 1.8 Page 4 of 28 Outdoor air Point PRO Antenna airPoint-PRO Outdoor AC/DC Adapter RJ-45 Ethernet Port 1.5 Inch pipe powerShot RF Cable Ethernet Cable U-bolt.
s m a r t Bridges to the future ... Revision 1.8 Page 5 of 28 Mounting the Antenna: Follow the mounting instructions provided by the antenna manufacturer and mount the antenna on the steel pipe. Antenna should be mounted on the same pipe as the airPoint-PRO Outdoor and positioned above it.
Revision 1.8 Page 6 of 28 Mounting the airPoint-PRO TOT AL Attach the mounting arm of the airPoint-PRO T OT AL unit with the 2pcs of U bolts to the pipe. Make sure to tighten both top and bottom U bolts, with nuts and spring washers. T ighten the nuts so that the mounting arm does not rotate on the pipe.
s m a r t Bridges to the future ... Revision 1.8 Page 7 of 28 U-bolt fixing pipe to Mounting Arm Mounting Arm airPoint-PRO T OT AL RJ45 Cable Cable Tie Wea ther proof Connector.
Revision 1.8 Page 8 of 28 to airPoin t-PRO / airPoint-PRO Outdoor / airPoint-PRO T O T AL RJ45 to Network / PC AC Adapter powerShot RJ45 Cable Cross Coupler switch SB2820 Cross Coupler switch Restore Default button Note: Restore Default button at the bottom side of the powerShot should be used to restore the device back to factory / WISP defaults.
s m a r t Bridges to the future ... Revision 1.8 Page 9 of 28 Connecting the airPoint-PRO series using Power Over Ethernet: The airPoint-PRO series is powered through the ethernet cable itself. This mode of operation gives flexibility for the user to position the airPoint-PRO at any location for best radio coverage.
Revision 1.8 Page 10 of 28 Software Installation System Requirements : Computer with Windows 98/ME/NT/2000/XP with working network card Installing airPoint-PRO Setup Software : Please insert the Setup Software CD into the CD-ROM drive of your PC. The CD will run automatically .
s m a r t Bridges to the future ... Revision 1.8 Page 1 1 of 28 Configuring the airPoint-PRO For Windows 98 / ME / NT / 2000 / XP The factory default parameters for airPoint-PRO l DHCP Client : Enabled (IP will be acquired from the DHCP Server on the LAN.
Revision 1.8 Page 12 of 28 b) Configuring airPoint-PRO using a standalone PC Connect the airPoint-PRO to the PC using cross CA T5 cable. Y ou can convert straight cable to cross using a cross connector provided. Make sure the power to the airPoint-PRO is ON.
s m a r t Bridges to the future ... Revision 1.8 Page 13 of 28 2. SETTING THE OPERA TIONAL MODE OF AIRPOINT -PRO The airPoint-PRO can operate in four different Modes, namely l Access Point - In this mode the airPoint-PRO is operating as a normal 802.1 1b compliant Access Point.
Revision 1.8 Page 14 of 28 1. Point to Point - This mode lets one airPoint-PRO talk to another airPoint-PRO wirelessly linking two Ethernet LANs behind together . 2. Point to MultiPoint - This mode lets multiple airPoint-PRO linking multiple Ethernet LANs.
s m a r t Bridges to the future ... Revision 1.8 Page 15 of 28.
Revision 1.8 Page 16 of 28 4. SECURITY T AB The airPoint-PRO can operate in four different Modes, namely l By default encryption is disabled which means the communication is not secure. In case you want to have a secure communication, ensure that the WEP encryption keys are set.
s m a r t Bridges to the future ... Revision 1.8 Page 17 of 28 Note: For WEP encryption the default format is HEX format. Incase of any wireless clients using the ASCII keys for the WEP , use the ASCII to HEX converter table for same. See Appendix B. Note: The Authentication type must be the same on the Clients and on the airPoint-PRO.
Revision 1.8 Page 18 of 28 The RSSI values are shown in dBm in ClientInfo and Associated AP Info T ab as per the internal formula. If you want your specific values to be shown in there, please store them in the table and set the option as "User Defined" from the Advanced T AB.
s m a r t Bridges to the future ... Revision 1.8 Page 19 of 28 The following information about all the associated clients is available in real time; the values are refreshed after every 5 seconds.
s m a r t Bridges to the future ... Revision 1.8 Page 20 of 28 Note: Client to Client communication T AB is disabled in the repeater mode If the client gets disassociated from the airPoint-PRO due to any reason ( power down etc ) you will continue to see the entry in the list for upto 5 minutes, before it is removed from the list.
Revision 1.8 Page 21 of 28 External Radius Server Authorization T o authorize clients using the External Radius Server please key in the following parameters and Click on Set Parameters button. l Source Port (Default Port is 1812) l Destination Port (supported in F/W 1.
Revision 1.8 Page 22 of 28 Configuring the airPoint-PRO in Client Bridge Mode In this mode the airPoint-PRO is operating as ethernet client, and it can associate only with another airPoint-PRO operating as an access point. In this Mode Site Survey and Link Status Tabs of simpleMonitor will be enabled.
s m a r t Bridges to the future ... Revision 1.8 Page 23 of 28 Configuring the airPoint-PRO in Wireless Bridge Mode In this mode airPoint-PRO can bridge 2 or more LANs wirelessly . Please select the Wireless Bridge T ab of simpleMonitor for configuring the airPoint-PRO in Wireless Bridge Mode.
Revision 1.8 Page 24 of 28 1. Point to Point This mode lets one airPoint-PRO talk to another airPoint-PRO wirelessly linking two Ethernet LANs together . A feature in this mode is that each airPoint-PRO must specify the MAC address of the airPoint-PRO at the opposite end of the wireless bridge.
s m a r t Bridges to the future ... Revision 1.8 Page 25 of 28 Repeater in Access Point Role The operation will be exactly same as Access Point serving the local clients, Access Point Mode information is equally applicable in this role. Please refer to Access Point Configuration details in Access Point Mode Section.
Revision 1.8 Page 26 of 28 5. Dial a Power Changing the output Power of airPoint-PRO Select Dial a Power T ab of simpleMonitor to change the output power of airPoint-PRO. This feature of airPoint-PRO allows the user to control the radio transmit power of the airPoint- PRO from the SimpleMonitor software.
s m a r t Bridges to the future ... Revision 1.8 Page 27 of 28 Restore Factory Default Settings If you forget the critical settings like WEP or Administrator Password of the airPoint-PRO, you can restore the airPoint-PRO to the Factory Default Settings as, 1.
Revision 1.8 Page 28 of 28 Appendix B ASCII to Hexadecimal Conversion T able Operating T emperature Range airPoint-PRO : 0 °C ~ +50 °C (+32 °F ~ +122 °F) airPoint-PRO Outdoor / T OT AL : -40 °C ~.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il SmartBridges airPoint Pro Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del SmartBridges airPoint Pro Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso SmartBridges airPoint Pro Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul SmartBridges airPoint Pro Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il SmartBridges airPoint Pro Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del SmartBridges airPoint Pro Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il SmartBridges airPoint Pro Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo SmartBridges airPoint Pro Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.