Manuale d’uso / di manutenzione del prodotto Parametric Equalizer del fabbricante SPL
Vai alla pagina of 27
OPTIMIZER parametric equalizer Owner´s Manual Operation . Applications . Measurements . Specifications ©1994 SPL electronics GmbH.
OPTIMIZER Owner´s Manual: Operation, Applications, Measurements, Specifications Written by Paul White and Hermann Gier Manual version 1.1/94 The information in this document has been carefully checked and is assumed to be correct.
3 OPTIMIZER C C O O N N T T E E N N T T S S I NTRODUCTION 4 I NST ALLA TION 7 C ONNECTORS 7 O PERA TING L EVEL 8 P OWER S UPPL Y 8 R EAR P ANEL 9 I NPUT & O UTPUT S PECIFICA TIONS 9 A PPLICA TIONS.
4 OPTIMIZER Congratulations on purchasing the Optimizer, one of the most advanced and musical sounding parametric equalizer currently available. The Optimizer is a highly specialized and creative equali- zer.
5 OPTIMIZER The Optimizer comprises four identical filter stages which can be configured for 4-band mono, dual 2-band mono or 2-band ste- reo operation. Each filter covers the same enormous frequency range 10Hz to 23kHz. Each filter has its own mode switch, so complex combina- tions of filter types can be used in the same signal path.
6 OPTIMIZER addition each filter is equipped with a notch-filter. Selecting the Notch mode overrides the mode switch selector. So com- plex combinations of filter types can be used in the same sig- nal path. For example, a parametric filter could be combi- ned with a High- and Low-pass and Notch filter.
7 OPTIMIZER tion as each filter is added to the signal path. The Optimizer overcomes this fault by using controllable all active output stages resulting in a significantly improved phase response, even when all four filters are linked up.
8 OPTIMIZER ce is not driving Optimizer´s filters sufficiently with the pro- viso that the Peak LED on the front panel is not continually flashing. This will achieve equalization at a lower signal level and will result in a more intensely processed sound.
9 OPTIMIZER Input- & output specifications XLR - balanced : Inputs: Electronically balanced (differential) transformerless Impedance: = 20kOhms Nominal input level: +6dB Input level selector: HIGH (0dB) LOW(-10dB) Maximum input level: +22dBm Input peak: LED indica- tes potential peak 3dB before actual clipping.
10 OPTIMIZER M M A A S S T T E E R R I I N N G G W W I I T T H H T T H H E E O O P P T T I I M M I I Z Z E E R R PARAMETRIC SET-UP: To use the Optimizer as a dual- channel, parametric equalizer proceed as follows: • Set all filters to PARAMETRIC • Set to DUAL mode and ensure MASTER BYPASS is out.
11 OPTIMIZER S S E E T T - - U U P P & & A A P P P P L L I I C C A A T T I I O O N N S S ons as a general studio equalizer, it is particularly effective at treating stereo programme material - either at the mixing stage or during post-production.
12 OPTIMIZER F F R R O O N N T T P P A A N N E E L L C C O O N N T T R R O O L L S S Peak-LED illu- minates 3dB before clip- ping Freq. range (1. or 4.
13 OPTIMIZER In mono mode the signal is routed from output 2 to the input of 3, this places all four sections in series. You can tap out after 2 as well as 4, you can use this feature for blends on the mixer. Each of the four OPTIMIZER filters is equipped with an individual bypass switch.
14 OPTIMIZER The Boost/Cut controls has two distinct functions depen- ding on the mode you are in. Boost and Cut as well as roll- off characteristics. Fig. 1: Dotted line: Max. boost and cut +/-12dB; Q = 1,5 Solid line: Phase response at Q = 1,5 Fig. 2: Dotted line: Max.
15 OPTIMIZER With proportional-Q the sig- nal level is dependent of the bandwidth setting - elimina- ting the need for constant level readjustment when changing the filter settings. Fig. 3: Q-values are between 0,2 and 1,5 at maximum boost and cut of +/- 12dB.
16 OPTIMIZER The frequency control (Hz) varies the filter frequency over the range selected with the Frequency Range switches. The two Frequency Range switches are used in combina- tion to select four frequency ranges. The switch positions are shown clearly on the Optimizer’s front panel.
17 OPTIMIZER The frequency control (Hz) will set the center-frequency when working in Parametric, Band-pass and Notch mode where-as in Low-pass mode it will determine the upper, and in High-pass the lower corner frequency. Below is a chart for pinpointing the exact frequencies.
18 OPTIMIZER 10 2045,1 2990,7 6180,6 20185 11 2380,5 3481,7 7096,3 21677 All frequencies in Hertz (Hz). The output control sets the output level of the filter sec- tion.
19 OPTIMIZER level changes due to dramatic boost or cut adjustments. The Notch switch puts the filter into notch filter mode. It provides a deep cut of over 60dB which can be varied in fre- quency to address any part of the audio spectrum, providing in excess of 60dB of attenuation at the center frequency.
20 OPTIMIZER a notch across the audio spectrum. A further creative use is to create a pseudo stereo image from a mono signal by split- ting the signal and applying different notches to each of the two channels. If these two channels are then panned left and right in the final mix, it creates an illusion of space.
21 OPTIMIZER of the audio spectrum to contrive a bandpass filter for the production of ‘telephone’ effects and similar treatments. In the High-pass and Low-pass modes, the Q control changes the filter characteristic from over damped to under damped, with the higher Q settings producing a tighter, more focused sound.
22 OPTIMIZER The following measurements show that the Optimizer´s phase response is very stable at high amplitudes. The doted line in fig. 16 illustrates the frequency response from 0Hz to 200kHz for two combined equalizers (band 1 and 2).
23 OPTIMIZER equalizers in modern recording technology. The Optimizer has an extremely broad frequency response from 0Hz to 200kHz that guaranties that the Optimizer´s filters operate with maximum tonal flexibility and without technically induced limitations.
24 OPTIMIZER Fig. 20: Noise Measurement "A" WTG: -92,56dB Boost/Cut = 0dB; Fig. 21: Noise Measurement "A" WTG: -108,79dB Boost/Cut = 0dB; Master-EQ: Bypass Fig. 22: Noise Measurement THD & Noise Boost/Cut = +12 dB; Bandwidth Q = 1.
25 OPTIMIZER Fig. 22: Noise Measurement CCIR 468: -83dB Boost/Cut = +12 dB; Bandwidth Q = 1.5; Frequency = 1kHz Fig. 23: Noise Measurement CCIR 468: -84dB Boost/Cut = 0 dB; Bandwidth Q = 1.5; Frequency = 1kHz Fig. 24: Common Mode Rejection of differential XLR Inputs Frequency range: 20Hz to 100kHz.
26 OPTIMIZER SPL electronics GmbH (hereafter called SPL) products are warranted only in the country where purchased, through the authorized SPL distributor in that country, against defects in material or workmanship.
SOUND PERFORMANCE LABORA TORY SPL electronics GmbH Hauptstrasse 59 D-41372 Niederkrüchten P.O.Box: Postfach #1227 D-41368 Niederkrüchten Tel. +49-(0)2163-8761 Fax +49-(0)2163-83028.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il SPL Parametric Equalizer è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del SPL Parametric Equalizer - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso SPL Parametric Equalizer imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul SPL Parametric Equalizer ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il SPL Parametric Equalizer, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del SPL Parametric Equalizer.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il SPL Parametric Equalizer. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo SPL Parametric Equalizer insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
