Manuale d’uso / di manutenzione del prodotto 4WD del fabbricante Stiga
Vai alla pagina of 12
STIGA PARK 4WD 92 M 107 M 107 M HD 121 M 110 Combi Pro 125 Combi Pro 8211-054 3-03.
2 125 Combi Pro 1 10/125 Combi Pro 121 M 107 M HD A B C B E F T orx T30 To r x T 3 0 1 10 /125 Combi Pro G H I 1 10/125 Comb i Pro 1 2 1 10/125 Combi Pro 121 M 107 M HD 1 10/125 Combi Pro 10 mm 10 mm .
3 92/107 M A B D B 10 mm 13 mm 13 mm J K L 1 10/125 Combi Pro M 11 13 107 M HD 15 9 92/107 12 92/107 M 14 16 10 92/107.
4 92/107 M 107 M HD 121 M 1/3 92/107 M 121 M 5 mm 1 10/125 Combi Pro 107 M HD 19 21 23 17 20 22 24 18.
5 O 1 10/125 Combi Pro Q 9,8 Nm P 24 Nm 24 Nm 92/107 M 107 M HD 121 M 45 Nm 1 10 Combi Pro O N 107 M HD 24 Nm 125 Combi Pro 27 29 25 28 30 26.
33 ENGLISH EN 1 GENERAL This symbol indicates W ARNING . Seri- ous personal injury and/or damage to property may result if the instructions are not followed car efully . Y ou must read these instructions for use and the machine’ s safety instructions carefully .
34 ENGLISH EN 2.3.3 Rear mounting The cutting deck’ s rear section is secured with the pins in fig. 13. 2.4 Controls, 92/107 M 2.4.1 Cutting heig ht adjustment The cutting height can be adjusted between 30 and 85 mm. The setting can be adjusted to a number of fixed positions using the lever .
35 ENGLISH EN 3.2 Installation of 107 M HD, 121 M 1. Place the cutting deck in position in front of the machine. 2. Install the following components on both wheel axles: • W asher (3:B). • Deck mount (3:C). • W asher (3:B). • Circlip (3:A). 3.
36 ENGLISH EN 3.5.2 Basic setting, 92/107 M, 121 M See fig. 17 and perform basic setting of 92/107 M and 121 M as follows: 1. Place the machine on a level floor . Requirements for floor fl atness: ±1 mm /m. No slope towards a floor drain or similar may occur in front of or behind the machine.
37 ENGLISH EN 5 MAINTENANCE 5.1 Preparation All service and all maintenance must be carried out on a stationary machine with the engine switched off. Prevent the machine from r olling by al- ways applying the parking brake.
38 ENGLISH EN 5.6.1 Separate blades The blades are replaceable. When replacing, both blades on the same blade bar must be replaced to avoid imbalance. T ightening torque: Screws (27:P) - 24 Nm Shear bolts (27:Q) - 9.8 Nm In the event of a collisi on, the shear bolts (27:Q) can break and the blades bend back.
www .stiga.com GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stiga 4WD è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stiga 4WD - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stiga 4WD imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stiga 4WD ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stiga 4WD, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stiga 4WD.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stiga 4WD. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stiga 4WD insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.