Manuale d’uso / di manutenzione del prodotto BTC6510GL del fabbricante Baumatic
Vai alla pagina of 28
BTC6510GL Cooker Hood.
User Manual for your Baumatic BTC6510GL Cooker Hood 60 cm Glass cooker hood in stainless steel NOTE : This User Instruction Manual contains imp ortant information, including safety & installation p oints, which will enable you to get the most out of your appliance.
3 Contents Page E n v i r o n m e n t a l n o t e 4 IMPORTAN T SAFETY IN FORMATION 5 – 7 Specifications of your BTC6510GL cooker hood 8 Using your Baumatic cooker hood 9 B e f o r e f i r s t u s e .
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch o ff and disconnect it from the power su pply. C ut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of th e information contained in this booklet, please contact the Baumatic Technical Department.
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, espe cially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room whe.
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your roo m, not steam.
Specifications of your BTC6510GL cooker hood Congratulations on purchasing a Baumatic cooker hood! PRODUCT DIMENSIONS Height: 550 mm – 1030 mm Width: 600 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTI.
Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality st ainless steel cleaner on ALL of the stainless steel areas of your cooker hood, before it is used for the first time.
o A = Indicator neons o B = Speed selection buttons = Low speed 10 = Medium speed = High speed o C = Light on/off button o Press one of the speed selection buttons to switch the hood on. It will run at the speed that you have selected (i.e. low, medium or high speed).
Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WA LL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth.
Maintenance Removing and cleaning the grease filters o First remove the grease filters by pulling down on the handle and pulling them away from the cooker hood. o Soak the grease filter in hot water and washing up liquid for about an hour. o Rinse them off thoroughly with hot water.
Changing a light bulb IMPORTANT: BEFORE AT TEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED TH E COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove the grease filter (as described on page 12). o Prior to touching the light bulbs ensure that they have cooled down.
Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY.
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filter.
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured ma rkings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (neutral), or coloured black .
o Do not tile, grout or silicone th is appliance to the wall. This appliance is designed to be surface mounted only. Installing your cooker hood IMPORTANT: YOU WILL HA VE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE.
2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B . 3) Using a drill bit with a 6 mm diameter, make holes in the wall on the positions that you have marked in step 2. 4) Insert rawl plugs into all of the holes that you have drilled.
5) Fasten the support screws halfway in, leaving them 10 mm out of the wall. 6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Fully tighten the anchoring screws into the wall.
Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the applianc e). o The other end of the ducting ho se should be connected to a discharge outlet that is suitable for cooking vapours.
21 0) Lift chimney section D upwards until it reaches the ceiling. You o Mark the side measurement of both sides of chimney section D 1) Take the fixing bracket ( E ) and place it between the two penc.
22 2) at you made in step 11. Insert rawl plugs into the holes and then se a screwdriver to secure the fixing bracket to the wall. ng ket to the wall, using the same method as you have just used to se cure the lower bracket. 3) Lift ch cure it to the fixing racket using the screws provided.
23 ompleting the installation you are setting the appliance to recirculation mode, then you should ee the “Fitting the carbon filters” ection on page 14. ment late, which is placed inside the cooker hood. The ppliance should now be connected to the electrical supply.
24 roubleshooting MPORTANT: If your cooker hood appears not to be operating tacting the Baumatic Service Department, lease refer to the checklist below. e e electricity supply o Check that the fan speed control is set correctly. e o The grease filters are dirty and require cleaning.
25 IMPORTANT: If your appliance appears not to be operating correctly, then yo u should disconnect it from your mains supply and then contact the E a is under guarante at the problem is not the result of an ppliance fault, then you may be liable for the cost of the call out m essary repair.
26 ire phone United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berksh RG2 0QX United Kingdom Sales Tele ales Fax (0118) 933 6900 S e (0118) 931 0035 Service Telephon 6911 (0118) 933 Service Fax (0118) 986 9124 Spares Telephone 44 Telephone (01235) 4372 Technical Advice (0118) 933 6933 E-mail: sales@baumatic.
27.
28.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Baumatic BTC6510GL è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Baumatic BTC6510GL - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Baumatic BTC6510GL imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Baumatic BTC6510GL ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Baumatic BTC6510GL, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Baumatic BTC6510GL.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Baumatic BTC6510GL. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Baumatic BTC6510GL insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
