Manuale d’uso / di manutenzione del prodotto 128T del fabbricante Troy-Bilt
Vai alla pagina of 20
Operator ’ s Manual T iller/Edger Model 128T W arning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-cov- ered or grass-covered land unless the engine ’ s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
2 For more details about your unit, visit our website at www .troybilt.com T ABLE OF CONTENTS Content Page Calling Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . .
TRAINING • Read this Owner’ s Manual and the sep- arate Engine Owner’ s Manual ver y care- fully before operating this equipment. Be completely familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly .
• Exercise extreme caution when on or crossing gravel drives, walks or roads. Stay alert for hidden hazards or traffic. Do not carry passengers. • After striking a foreign object, stop the engine,.
INTRODUCTION Read these instructions in their entirety before you attempt to assemble or op- erate your new equipment. The Border/Edger Attachment (H, Figure 5) does not need to be installed until you are ready to do edging projects (refer to instructions in this Section).
6 4. Do not mix fuel directly in engine fuel tank. Always use a clean, safety-ap- proved fuel container . • T o Mix: A. Fill a clean, approved container one quarter full with recommended gasoline. B. Add recommended amount of oil per Chart 1: FUEL MIXTURE.
Features and Controls 3 Section KNOW YOUR EQUIPMENT READ THIS OWNER ’ S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR EQUIPMENT . Know the location and function of all features and controls on the equipment. Save this manual for future reference.
PRE-ST AR T PREP ARA TION Before starting the engine, perform the following checks and services: 1. Disconnect the spark plug wire from the spark plug. 2. Move the engine On/Off switch to the OFF position. 3. Check the three plastic cable ties (J, Figure 5).
Allow the engine to warm up for several seconds. If engine either fails to start or to continue running, push in primer bulb two (2) times. Grasp starter rope and pull with a rapid, full stroke, up to ten (10) times. TROUBLESHOOTING: Push the primer bulb in two (2) more times.
10 USING THE EDGER A TT ACHMENT The Edger Attachment makes clean, sharp edges next to walkways, driveways, paths, planted areas, patios, etc. See Assembly Steps, STEP 4: in Section 2 for instructions on attaching this attachment. T ake your time when edging.
EQUIPMENT MAINTENANCE T ransmission Maintenance The transmission was lubricated at the factory and should not require any further lubrication. However , you should check the lubricant level after the first five (5) hours of opera- tion and every twenty-five (25) operating hours thereafter .
If the engine is running poorly or has low power while tilling, an adjustment to the carburetor may solve the problem. How- ever , first inspect and service the spark plug and the air filter before making a carburetor adjustment.
Arranging Tines for Stony Soil Conditions 1. Prop the machine forward so it rests on the front of the tubular carrying handle. The work surface should be flat and firm. 2. Remove the hitch pin (A, Figure 16) from both sides of the unit. Remove both outer tine sections.
14 TROUBLESHOOTING Before performing any of the corrections in this T roubleshooting Chart, refer to the appropriate information contained in this Manual and the Engine Owner ’ s Manual for the correct safety precautions and ser vicing procedures. Contact your local authorized Engine Service Dealer for engine ser vice.
15 1 1915039 T ransmission Case - left-side. (Incl. pressed-in bushing) . . . . . . . . . . . . 1 2 1915040 T ransmission Case - right-side. (Incl. pressed-in bushing) . . . . . . . . . . . . 1 3 1983632 Oil Seal . . . . . . . . . . . . . . . . . . . .
16 1 5 13 13 13 17 18 46 42 42 SEE PREVIOUS P AGE 49 48 47 21 31 32 34 33 26 28 29 30 25 24 23 22 27 43 42 42 18 19 19 38 39 41 40 40 36 37 35 45 16 15 14 45 4 6 9 3 8 44 44 7 Parts List Model 128T.
17 1 1918303 Handlebar Assembly . . . . . . . . . . . . . . . . . . 1 3 777I00007 Decal - Starting Stabilization . . . . . . . . . . . . 1 4 777I00009 Decal - Throttle/T ines Lever Operation . . . . . 1 5 1917451 Handlebar Grip, PVC . . . . . . . . . .
18 Notes.
19 A ccessories and Attachments . . . . . . . . . . . . . . . . . . . . . . .14 Aerator Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MANUF ACTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by T roy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Troy-Bilt 128T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Troy-Bilt 128T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Troy-Bilt 128T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Troy-Bilt 128T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Troy-Bilt 128T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Troy-Bilt 128T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Troy-Bilt 128T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Troy-Bilt 128T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.