IT
InFocus logo
Manuale d'uso ufficiale

InFocus DS 14DAL

70 pagine·1.5 MB·Trapano a batteria·PDF·ENJA
InFocus DS 14DAL
Indice dei contenuti 18 sezioni Variable speed · DS 14DAL · GENERAL SAFETY RULES · PRECAUTIONS FOR CORDLESS DRIVER DRILL · … MostraNascondi
Page 1 of the InFocus DS 14DAL user manual — Variable speed
Pagina 1 · clicca per ingrandire
Pagina 1

Cordless Driver Drill Akku-bohrschrauber Perceuse-visseuse à batterie Trapano-avvitatore a batteria Snoerloze boor-schroefmachine Taladro atornillador a batería Berbequim aparafusadora a bateria ∆ραπανκατσά ιδ µπαταρίας

Variable speed

DS 14DAL

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste instruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções. ∆ιαάστε πρ σεκτικά και καταν ήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso δηγίες ειρισµ ύ

Page 2 of the InFocus DS 14DAL user manual — Variable speed
Pagina 2 · clicca per ingrandire
Pagina 2
InFocus DS 14DAL — Variable speed diagram (page 2)
Fig. 1 · Variable speed
Page 3 of the InFocus DS 14DAL user manual — Variable speed
Pagina 3 · clicca per ingrandire
Pagina 3
InFocus DS 14DAL — Variable speed diagram (page 3)
Fig. 2 · Variable speed
InFocus DS 14DAL — Variable speed diagram (page 3)
Fig. 3 · Variable speed
Page 4 of the InFocus DS 14DAL user manual — Variable speed
Pagina 4 · clicca per ingrandire
Pagina 4
InFocus DS 14DAL — Variable speed diagram (page 4)
Fig. 4 · Variable speed
Page 5 of the InFocus DS 14DAL user manual — Variable speed
Pagina 5 · clicca per ingrandire
Pagina 5
EnglishDeutschFrançaisItaliano 1Rechargeable batteryAufladbare BatterieBatterie rechargeableBatteria ricaricabile da 2LatchVerriegelungTaquetFermo 3Pull outHerausziehenTirer vers l’extérieurEstrarre 4InsertEinsetzenInsérerInserire 5HandleHandgriffPoignéeImpugnatura 7InsertEinsetzenInsérerInserire 8Pilot lampKontrollampeLampe témoinSpia 9Hole for connecting the rechargeable batteryAnschlußloch für LadebatterirOrifice de raccordemente de la batterie rechargeableForo di collegamento della batteria ricaricabile 0Drill markBohrer-ZeichenIndice de forageSimbolo di foratura AClutch dialKupplungsskalaSélecteur de débrayageGhiera frizione BTriangle markDreiecksmarkierungTriangleSimbolo del triangolo CWeakSchwachFaibleDebol DStrongStarkFortForte ELineLinieLigneLinea FShift knobSchaltknopfBouton de décalageManopola di comando GLow speedKleine GeschwindigkeitVitesse ralentieBassa velocità HHigh speedGroße GeschwindigkeitVitesse élevéeAlta velocità IHook with lightHaken mit BeleuchtungCrochet muni d’un éclairageGancio munito di lampada JLoosenLösenDesserrerAllentare KSpringFederRessortMolla LLarger diameter faces awayDer große Durchmesser weist zur anderen SeiteGros diamètre dirigé vers l’extérieurDiametro più grande lontano da sé MSwitchSchalterInterrupteurInterruttore NPhillips-head screwdriverKreuzschlitzschraubenzieherTournevis à tête PhillipsCacciavite con testa a croce OScrewSchraubeVisVite PArrowPfeilFlècheFreccia QHook coverHakenabdeckungCache de crochetCoperchio gancio RIndentationEinkerbungEntailleTacca SProtuberanceVorsprungSaillieSporgenza TAAAA batteriesBatterien der Größe AAAAPiles AAAAPile AAAA USleeveManschetteManchonCollare VTightenAnziehenSerrerStringere WLoosenLösenDesserrerAllentare XTrigger switchTriggerDéclencheurInterruttore YSelector buttonWählhebelSélecteurSelettore ZR and L marksR und L ZeichenIndices R et LSegno R , L [Wear limitVerschließgrenzeLimite d’usureLimite di usura \Nail of carbon brushKlaue der KohlebürsteClou de balai en carboneChiodo di spazzola di carbone ]Protrusion of carbon brushKrempe der KohlebürsteSaillie de balai en carboneSporgenza di spazzola di carbone `Contact portion outside brush tubeKontaktteil außerhalb des BürstenrohrsSection de contact à l’extérieur du tube de balaiParte di contatto fuori dal tubo spazzola
Page 6 of the InFocus DS 14DAL user manual — Variable speed
Pagina 6 · clicca per ingrandire
Pagina 6
NederlandsEspañolPortuguêsΕλληνικά 1Oplaadbare batterijBatería recargable deBateria recarregável deΕπανα ρτιµενη 2VergrendelingCierreLingüetaΜάνδαλ 3UittrekkenSacarRetirarΤραήτε έω 4InstekenInsertarInserirΕισωρήστε 5HandgreepAsideroCaboερ ύλι 7InstekenInsertarInserirΕισωρήσετε 8ControlelampjeLámpara pilotoLâmpada piloto∆ κιµαστική λάµπα 9Aansluiting voor oplaadbare batterijAgujero para conectar la batería recargableOrifício para conectar a bateria recarregávelΤρύπα για την σύνδεση της επανα ρτιµενης µπαταρίας 0Boor-markeringMarca del taladroSímbolo da brocaΣηµάδι τρυπανι ύ AKoppelingsinstellingDial del embragueDisco de engateΚαντράν συµπλέκτη BDriehoekjeMarca de triánguloMarca de triânguloΣηµάδι τριγών υ CZwakDébilFracoΑδύνατ DSterkFuerteForte∆υνατ EStreepjeLíneaLinhaΓραµµή FToerenschakelaarMando de cambioComutadorΚ υµπί αλλαγής GLaag toerentalVelocidad altaVelocidade baixaαµηλή ταύτητα HHoog toerentalVelocidad bajaVelocidade altaΥψηλή ταύτητα IHaak met lampGancho con luzGancho com luzΓάντ ς µε ως JLosdraaienAflojarAfrouxarXαλαρώστε KVeerResorteMolaΕλατήρι LDe grotere diameter wijst van u vandaanEl diámetro más grande queda en dirección opuestaO diâmetro maior dá para foraΗ µεγαλύτερη διάµετρ ς λέπει πρ ς άλλη κατεύθυνση MSchakelaarInterruptorComutador∆ιακπτης NKruiskopschroevendraaierDestornillador con cabeza PhillipsChave PhillipsΚατσαίδι κε αλής Phillips OSchroefTornilloParafusoΒίδα PPijlFlechaSetaΒέλ ς QAfdekking haakCubierta del ganchoTampa do ganchoΚάλυµµα αγκίστρ υ RInkepingIndentaciónEntalheΑυλάκωση SUitsteekselSalienteProtuberânciaΠρ ε ή TAAAA batterijenPilas AAAAPilhas AAAAΑΑΑΑ µπαταρίες UKlembusManguitoManguitoΠερίληµα VAandraaienApretarApertarΣ ίτε WLosdraaienAflojarAfrouxarαλαρώστε XTrekkerschakelaarConmutador de gatilloInterruptor de comandoΣκανδάλη διακπτης YOmzetschakelaarBotón selectorBotão seletorΚ υµπί επιλ γέα ZR en L merktekensMarcas R y LMarcas R e LR και L σηµάδια [SlijtagegrensLímite de usoLimite de desgaste.ρι θ ράς \Nagel van koolborstelUña de escobilla de carbónPrego da escova de carvãoΚαρ ί καρ υνακι ύ ]Uitsteeksel van koolborstelSaliente de escobilla de carbónSaliência da escova de carvãoΠρ ε ή καρ υνακι ύ `Contact-gedeelte buiten de borstelbuisTubo exterior de la parte de contacto de la escobilla de carbónSegmento de contato no exterior do tubo da escovaΤµήµα επα ής έω απ τ σωλήνα της ψήκτρας
Page 7 of the InFocus DS 14DAL user manual — GENERAL SAFETY RULES
Pagina 7 · clicca per ingrandire
Pagina 7

GENERAL SAFETY RULES

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust

SAVE THESE INSTRUCTIONS 1) Work area a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive

extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust of fumes. c) Keep children and bystanders away while operating

4. Power tool use and care a) Do not force the power tool. Use the correct

a power tool. Distractions can cause you to lose control.

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not

2. Electrical safety a) Power tool plugs must match the outlet.

turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source before

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or

conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for

binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc.,

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3. Personal safety a) Stay alert, watch what you are doing and use

in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation.

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Avoid accidental starting. Ensure the switch is in

5. Service a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons.

Page 8 of the InFocus DS 14DAL user manual — CHARGER
Pagina 8 · clicca per ingrandire
Pagina 8

PRECAUTIONS FOR CORDLESS DRIVER DRILL

9. Using an exhausted battery will damage the charger. 10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.

1. Always charge the battery at a temperature of 0 – 50°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 50°C. The most suitable temperature for charging is that of 20 – 25°C. 2. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 7. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 and 2 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function. 1. When the battery power remaining runs out (The battery voltage drops to about 8V), the motor stops. In such case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

SPECIFICATIONS

POWER TOOL

ModelDS14DAL No-load speed (Low/High)0–350/0–1200 min–1 CapacityDrillingWood (Thickness 18 mm)27 mm Metal (Thickness 1.6 mm)Steel: 13 mm, Aluminum: 13 mm DrivingMachine screw6 mm Wood screw6.8 mm (diameter) × 50 mm (length) (Requires a pilot hole) Rechargeable batteryEBM1430R: Li-ion 14.4 V (3.0 Ah 8 cells) Weight1.6 kg

CHARGER

ModelUC18YRL Charging voltage7.2 – 18 V Weight0.6 kg
Page 9 of the InFocus DS 14DAL user manual — APPLICATIONS
Pagina 9 · clicca per ingrandire
Pagina 9

STANDARD ACCESSORIES

BATTERY REMOVAL/INSTALLATION

DS14DAL1 Plus driver bit (No.2) 1 2 Charger (UC18YRL) 1 3 Plastic case 1
1. Battery removal Hold the handle tightly and push the battery latch to remove the battery (see Figs. 1 and 2 ). CAUTION:

Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (see Fig. 2).

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

CHARGING

1. Battery (EBM1430R)

Before using the driver drill, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle. When the power cord is connected, the charger’s pilot lamp will blink in red. (At 1-second intervals) 2. Insert the battery into the charger. Firmly insert the battery into the charger till it contacts the bottom of the charger and checking the polarities as shown in Fig. 3. CAUTION: If the batteries are inserted in the reverse direction,

not only recharging will become impossible, but it may also cause problems in the charger such as a deformed recharging terminal. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red. (At 1-second intervals) (See Table 1) (1) Pilot lamp indication

Optional accessories are subject to change without notice.

APPLICATIONS

Driving and removing of machine screws, wood

screws, tapping screws, etc. Drilling of various metals Drilling of various woods

The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

Indications of the pilot lamp Charge status lamp(RED)Before chargingBlinks Lights for 0.5 seconds. Does not light for 0.5 (RED) seconds. (off for 0.5 seconds) While chargingLights Lights continuously (RED) Charging completeBlinks Lights for 0.5 seconds. Does not light for 0.5 (RED) seconds. (off for 0.5 seconds) Charging impossibleFlickers Lights for 0.1 seconds. Does not light for 0.1 (RED) seconds. (off for 0.1 seconds)Malfunction in the battery or the charger Overheat lamp (GREEN)Overheat standbyLights Lights continuously (GREEN)Battery overheated. Unable to charge (Charging will commence when battery cools).

Table 1

Page 10 of the InFocus DS 14DAL user manual — NOTE:
Pagina 10 · clicca per ingrandire
Pagina 10

(2) Regarding the temperatures of the rechargeable

If the battery is recharged when it is warm due to

battery The temperatures for rechargeable batteries are as shown in Table 2, and batteries that have become hot should be cooled for a while before being recharged.

battery use or exposure to sunlight, the pilot lamp map light in green. The battery will not be recharged. In such a case, let the battery cool before charging. When the pilot lamp flickers in red (at 0.2-second

intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Table 2 Recharging ranges of batteries

Rechargeable batteriesTemperatures at which the battery can be recharged EBM1430R0°C – 50°C

PRIOR TO OPERATION

1. Setting up and checking the work environment Check if the work environment is suitable by following the precautions.

(3) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.

HOW TO USE

Table 3 Charging time (At 20°C)

1. Confirm the clutch dial position (see Fig. 4) The tightening torque of this unit can be adjusted according to the clutch dial position, at which the clutch dial is set. (1) When using this unit as a screwdriver, line up the one
Charger BatteryUC18YRL EBM1430RApprox.45 min.

of the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. (2) When using this unit as a drill, align the clutch dial

NOTE:

The charging time may vary according to temperature and power source voltage.

” with the triangle mark on the outer body. CAUTION: The clutch dial cannot be set between the numerals

4. Disconnect the charger’s power cord from the receptacle. 5. Hold the charger firmly and pull out the battery. NOTE:

“1, 3, 5 ... 22” or the dots. Do not use with the clutch dial numeral between

After operation, pull out batteries from the charger first, and then keep the batteries properly.

“22” and the line at the middle of the drill mark. Doing so may cause damage. (See Fig. 5) 2. Tightening torque adjustment (1) Tightening torque

Regarding electric discharge in case of new batteries, etc.

Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the clutch dial , and the dots. The tightening toque at position “1” is the weakest and the torque is strongest at the highest number. (See Fig. 4) (3) Adjusting the tightening torque

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

Rotate the clutch dial and line up the numbers “1, 3, 5, ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. Adjust the clutch dial in the weak or the strong torque direction according to the torque you need. CAUTION: The motor rotation may be locked to cease while the

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION: When the battery charger has been continuosly used,

unit is used as drill. While operating the driver drill, take care not to lock the motor. Too long hammering may cause the screw broken

the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

due to excessive tightening.

drill mark “

Page 11 of the InFocus DS 14DAL user manual — PRIOR TO OPERATION
Pagina 11 · clicca per ingrandire
Pagina 11
3. Change rotation speed Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (see Figs. 6 and 7 ). When the shift knob is set to “LOW”, the drill rotates at a low speed.!»en set to “HIGH”, the drill rotates at a high speed. CAUTION: When changing the rotational speed with the shift

When setting the shift knob to “HIGH” (high speed)

and the position of the clutch dial is “17” or “22”, it may happen that the clutch is not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or battery may be burnt. 4. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.

knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears.

WorkSuggestions DrillingWoodUse for drilling purpose. Steel Aluminum DrivingMachine screwUse the bit or socket matching the screw diameter. Wood screwUse after drilling a pilot hole.
5. How to select tightening torque and rotational speed
UseClutch PositionRotating speed selection (Position of the shift knob) LOW (Low speed)HIGH (High speed) DrivingMachine screw1 – 22For 4 mm or smaller diameter screws.For 6 mm or smaller diameter screws. Wood screw1 –For 6.8 mm or smaller nominal diameter screws.For 3.8 mm or smaller nominal diameter screws. DrillingWoodFor 27 mm or smaller diameters.For 18 mm or smaller diameters. MetalFor drilling with a metal working drill bit.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

be considered as general standard. As different types of tightening screws and different materials to be tightened are used in actual works proper adjustments are naturally necessary. When using the driver drill with a machine screw

arrow (A) and turn in the direction of arrow (B). (Fig. 8) (b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position CAUTION:

at HIGH (high speed), a screw may damage or a bit may loose due to the tightning torque is too strong. Use the driver drill at LOW (low speed) when using a machine screw. NOTE:

Incomplete installation of the hook may result in bodily injury when used. (a) Securely hold the main unit and remove the screw

The use of the battery EBM1430R in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up. 6. Using the light equipped hook The light equipped hook can be installed on the right or left side and the angle can be adjusted in 5 steps between 0° and 80°.

using a slotted head screwdriver or a coin. (Fig. 9) (b) Remove the hook and spring. (Fig. 10) (c) Install the hook and spring on the other side and

securely fasten with screw. (Fig. 11) NOTE:

Pay attention to the spring orientation. Install the spring with larger diameter away from you. (Fig. 11) (3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically after 15 minutes.

Table 4 · Table 5

Page 12 of the InFocus DS 14DAL user manual — MAINTENANCE AND INSPECTION
Pagina 12 · clicca per ingrandire
Pagina 12

(b) The direction of the light can be adjusted within

sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. 8. Automatic spindle-lock mechanism This unit has automatic spindle-lock mechanism for quick bit changes. 9. Confirm that the battery is mounted correctly 10. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 17) (The L and R marks are provided on the selector button.) 11. Switch operation When the trigger switch is depressed, the tool rotates.

the range of hook positions 1 - 5. (Fig. 12) Lighting time

AAAA manganese batteriesapprox. 15 hrs. AAAA alkali batteries: approx. 30 hrs. CAUTION:

Do not look directly into the light. Such actions could result in eye injury. (4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1). (Fig. 13) Remove the hook cover by pushing in the direction of the arrow. (Fig. 14) (b) Remove the old batteries and insert the new

batteries. Align with the hook indications and position the plus (+) and minus (–) terminals correctly. (Fig. 15) (c) Align the indentation in the hook main body with

When the trigger is released, the tool stops. The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE: A buzzing noise is produced when the motor is about

the protuberance of the hook cover, press the hook cover in the direction opposite to that of the arrow shown in Fig. 14 and then tighten the screw. Use commercially available AAAA batteries (1.5 V). NOTE:

to rotate; This is only a noise, not a machine failure.

MAINTENANCE AND INSPECTION

Do not tighten the screw excessively. Such action could strip the screw threads. CAUTION: Failure to observe the following can result in battery

1. Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Inspecting the carbon brushes (Fig. 18) The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely whthin the brush holders. NOTE:

leakage, rust or malfunction. Position the plus (+) and minus (–) terminals correctly. Replace both batteries at the same time. Do not mix old and new batteries. Remove exhausted batteries from the hook immediately. Do not discard batteries together with normal trash

and do not throw batteries into fire. Store batteries out of the reach of children. Use batteries correctly in accordance with the battery

specifications and indications. 7. Mounting and dismounting of the bit (1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front) to open the clip on the keyless chuck. After inserting a driver bit, etc., into the keyless drill chuck, and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig. 16) If the sleeve becomes loose during operation, tighten

When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 999054. 5. Replacing carbon brushes Take out the carbon brush by first removing the brush cap and then hooking the protrusion of the carbon brush with a flat head screw driver, etc., as shown in Fig. 20. When installing the carbon brush, choose the direction so that the nail of the carbon brush agrees with the contact portion outside the brush tube. Then push it in with a finger as illustrated in Fig. 21. Lastly, install the brush cap. CAUTION:

it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front), and then take out the bit ect. (See Fig. 16) NOTE:

If the sleeve is tightened in a state where the clip of the keyless chuck is opened to a maximum limit, a click noise may occur. This is the noise that occurs when the loosening of the keyless chuck is prevented and is not a malfunction. CAUTION: When it is no longer possible to loosen the sleeve,

Be absolutely sure to insert the nail of the carbon brush into the contact portion outside the brush tube. (You can insert whichever one of the two nails provided).

use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 11 and then turn the

Page 13 of the InFocus DS 14DAL user manual — GUARANTEE
Pagina 13 · clicca per ingrandire
Pagina 13

Caution must be exercised since any error in this operation can result in the deformed nail of the carbon brush and may cause motor trouble at an early stage. 6. Cleaning on the outside When the driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 7. Storage Store the driver drill in a place in which the tempera ture is less than 40°C and out of reach of children. 8. Service parts list CAUTION:

Information concerning airborne noise and vibration The measured values were determined according to EN 60745 and declared in accordance with ISO 4871.

Measured A-weighted sound pressure level70 dB(A) Uncertainty KpA: 3 dB(A)

The typical weighted root mean square acceleration value: 2.0 m/s2.

Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with statutory/country specific regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center.

Blue: – Neutral Brown: – Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE: This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except United Kingdom.

Wear ear protection

Fai una domanda su InFocus DS 14DAL

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo InFocus DS 14DAL

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

InFocus DS 14DAL manuale in PDF

70 pagine·1.5 MB·Trapano a batteria·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…