




- the times when the tool is switched off or when
it is running but not actually doing the job, may significantly reduce the exposure level
Thank you for buying this Ferm product. By doing so you now have an excellent product, delivered by one of Europe’s leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.
Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns
Product information Fig. A 1. Handgrip 2. On/off switch 3. Cut depth clamping knob 4. Power cord 5. Saw blade safety guard 6. Hexagon screw 7. Soleplate 8. Retaining ring 9. Saw blade 10. Rip fence 11. Rip fence clamping knob 12. Sawing angle clamping knob 13. Shaft locking knob 14. Protractor 15. Knob 16. Safety switch 17. Carbon brush screw
The pictures mentioned in the text are corresponding with the pictures at page 2
For your own safety and for the safety of others, please read these instructions carefully before using this appliance. It will help you understand your product more easily and avoid unnecessary risks. Keep this instruction manual in a safe place for future use.
Technical specifications Voltage 230-240 V Frequency 50 Hz Power input 1200 W No load speed 5500/min Saw blade dimensions Ø185xØ20x2.4 mm Number of teeth Z24 Max sawing depth 90° 65 mm Max sawing depth 45° 43 mm IP Class IP 20 Weight 3,47 kg Lpa (sound pressure level) 92.8+3 dB(A) Lwa (sound power level) 103.8+3 dB(A) aw(vibration value) 3.787+1.5 m/s2
Contents of packing 1 Circular handsaw 1 Rip fence 1 TCT Saw blade Ø185 mm 1 Allen key 1 Set carbon brushes
Check first whether or not the delivery has been damaged by transport and/or whether all the parts are present.
Vibration level The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 62841; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with
Explanation of the symbols
Denotes risk of personal injury, loss of life or damage to the tool in case of non- observance of the instructions in this manual.
different or poorly maintainted accessories, may significantly increase the exposure level
Indicates electrical shock hazard.

Wear ear and eye protection
Wear a dust mask. Working with wood, metals and other materials may produce dust that is harmful to health. Do not work with material containing asbestos
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. b) Do not reach underneath the workpiece. The
a) Maintain a firm grip with both hands on the
saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken. b) When blade is binding, or when interrupting
guard cannot protect you from the blade below the workpiece. c) Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece. d) Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control. e) Hold power tool by insulated gripping surfaces
a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding. c) When restarting a saw in the workpiece, centre
when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and shock the operator. f) When ripping always use a rip fence or straight
the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted. d) Support large panels to minimise the risk of
edge guide. This improves the accuracy of cut and reduces the chance of blade binding. g) Always use blades with correct size and
shape (diamond versus round) of arbour holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control. h) Never use damaged or incorrect blade
blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. e) Do not use dull or damaged blades.
washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback. f) Blade depth and bevel adjusting locking levers
Causes and operator prevention of kickback • Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing
must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
Keep bystanders away

g) Use extra caution when making a “plunge
cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
Safety instructions lower guard a) Check lower guard for proper closing before
each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. b) Check the operation of the lower guard spring.
If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build- up of debris. c) Lower guard should be retracted manually
only for special cuts such as “plunge cuts” and “compound cuts.” Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. d) Always observe that the lower guard is covering
the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

Electrical safety When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions. Keep these instructions in a safe place!
Always check that the power supply corresponds to the voltage on the rating plate.
Class II machine – Double insulation – You don’t need any earthed plug.
Replacing cables or plugs If the mains cable becomes damaged, it must be replaced with a special mains cable available from the manufacturer or the manufacturer’s customer service. Dispose of old cables or plugs immediately after replacing them with new ones. It is dangerous to connect the plug of a loose cable to a socket.
Using extension cables Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely.
Use of hearing protection is recommended while operating the circular saw.
Before adjusting the saw, make sure the plug is removed from the socket.

Cleaning Keep the ventilation slots of the machine clean to prevent overheating of the engine. Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.
Let the saw do the job. Do not put undue pressure on the circular saw.
Make sure that the machine is not live when carrying out maintenance work on the motor.
The machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.
Troubleshooting Below we have listed a few probable causes and solutions to which you can refer if your circular saw does not function properly.
Frequent use will cause the carbon brushes to wear down. Regular inspection, after every 30 hours of use, is essential. If the brushes have worn down to less than 4 mm, replace.
Lubrication The machine requires no additional lubrication.
Faults Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

CSM1039




DECLARATION OF CONFORMITY
CSM1039 - CIRCULAR SAW
(EN) We declare under our sole responsibility that this product is in conformity with
parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení. (SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade
directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations: (DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt der Direktive
s nasledujúcimi normami a predpismi: Je v súlade s normou 2011/65/EÚ Európske- ho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení. (SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja nasledn-
2011/65/EU des Europäischen Parlaments und des Rats vom 8. Juni 2011 über die Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen und elektronischen Geräten entspricht. den folgenden Standards und Vorschriften entspricht: (NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan
jim standardom terpredpisom: je v skladu z direktivo 2011/65/EU Evropskega parla- menta in Sveta z dne 8. junij 2011 o omejevanju uporabe določenih nevarnih snovi v električni in elektronski opremi. (PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte
de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 juni 2011 betreffende beperking van het gebruik van bepaalde gevaarlijke stoffen in elektrische en elektronische apparatuur en in overeenstemming is met de volgende standaarden en reguleringen: (FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux
w następujących normach i przepisach: jest zgodny z Dyrektywą 2011/65/UE Parla- mentu Europejskiego i Rady z dnia 8 czerwca 2011 r. w sprawie ograniczenia stoso- wania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronic- znym. (LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau
standards et directives suivants: est conforme à la Directive 2011/65/EU du Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d’usage de certaines substances dangereuses dans l’équipement électrique et électronique. (ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con
paminėtus standartus arba nuostatus: atitinka 2011 m. birželio 8 d. Europos Parlamento ir Tarybos direktyvą 2011/65/EB dėl tam tikrų pavojingų medžiagų naudojimo elektros ir elektroninėje įrangoje apribojimo. (LV) Ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai
las siguientes normas y estándares de funcionamiento: se encuentra conforme con la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011 sobre la restricción del uso de determinadas sustancias peligrosas en los equipos eléctricos y electrónicos. (PT) Declaramos por nossa total responsabilida-de que este produto está em
2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās. (ET) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem stand-
artiem un nolikumiem: ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās. (RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în
conformidade e cumpre as normas e regulamentações que se seguem: está em conformidade com a Directiva 2011/65/EU do Parlamento Europeu e com o Conselho de 8 de Junho de 2011 no que respeita à restrição de utilização de determinadas substâncias perigosas existentes em equipamento eléctrico e electrónico. (IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle
conformitate cu următoarele standarde sau directive: este în conformitate cu Directiva 2011/65/UE a Parlamentului European şi a Consiliului din 8 iunie 2011 cu privire la interzicerea utilizării anumitor substanţe periculoase la echipamentele electrice şi electronice. (HR) Izjavljujemo pod vlastitom odgovornoĻśu da je strojem ukladan sa slijedeśim
normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del Parlamento Europeo e del Consiglio dell’8 giugno 2011 sulla limitazione dell’uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche. (SV) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande
standardima ili standardiziranim dokumentima i u skladu sa odredbama: usklađeno s Direktivom 2011/65/EU europskog parlamenta i vijeća izdanom 8. lipnja 2011. o ograničenju korištenja određenih opasnih tvari u električnoj i elektroničkoj opremi. (SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili
standarder och bestämmelser: uppfyller direktiv 2011/65/EU från Europeiska parlamentet och EG-rådet från den 8 juni 2011 om begränsningen av användning av farliga substanser i elektrisk och elektronisk utrustning. (FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat
normama: usaglašen sa direktivom 2011/65/EU Evropskog parlamenta i Saveta od 8.juna.2011. godine za restrikciju upotrebe određenih opasnih materija u električnoj i elektronskoj opremi. (RU) Под свою ответственность заявляем, что данное изделие соответствует
standardit ja säädökset: täyttää Euroopan parlamentin ja neuvoston 8. kesäkuuta 2011 päivätyn direktiivin 2011/65/EU vaatimukset koskien vaarallisten aineiden käytön rajoitusta sähkö- ja elektronisissa laitteissa. (NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende
следующим стандартам и нормам: соответствует требованиям Директивы 2011/65/EU Европейского парламента и совета от 8 июня 2011 г. по ограничению использования определенных опасных веществ в электрическом и электронном оборудовании (UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає
standarder og regler: er i samsvar med EU-direktivet 2011/65/EU fra Europa- parlamentet og Europa-rådet, pr. 8 juni 2011, om begrensning i bruken av visse farlige stoffer i elektrisk og elektronisk utstyr. (DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende
наступним стандартам і нормативам: задовольняє вимоги Директиви 2011/65/ ЄС Європейського Парламенту та Ради від 8 червня 2011 року на обмеження використання деяких небезпечних речовин в електричному та електронному обладнанні. (EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω
standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra Europa-Parlamentet og Rådet af 8. juni 2011 om begrænsning af anvendelsen af visse farlige stoffer i elektrisk og elektronisk udstyr. (HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben
κανονισμούς και πρότυπα: συμμορφώνεται με την Οδηγία 2011/65/ΕΕ του Ευρωπαϊκού Κοινοβουλίου και του Συμβουλίου της 8ης Ιουνίου 2011 για τον περιορισμό της χρήσης ορισμένων επικίνδυνων ουσιών σε ηλεκτρικό και ηλεκτρονικό εξοπλισμό. (BG) Ние декларираме на наша отговорност, че този продукт отговаря на съответствие с
megfelel az alábbi szabványoknak és előírásoknak: je v souladu se směrnicí 2011/65/EU Evropského parlamentu a Rady EU ze dne 8. června 2011, která se týká omezení použití určitých nebezpečných látek v elektrických a elektronických zařízeních. (CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s
Директива 2011/65/ЕС на Европейския парламент и на Съвета от 8 юни 2011 г. относно ограничението на употребата на определени опасни вещества в електрическото и електронното оборудване, в съответствие сследните стандарти и наредби:
EN61000-3-2, EN61000-3-3
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Zwolle, 01-07-2019 H.G.F Rosberg CEO FERM
FERM - Lingenstraat 6 - 8028 PM - Zwolle - The Netherlands

1907-17
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.